PD17P709A_15 Datasheet, PDF (30/38 Pages) Renesas Technology Corp – 4-BIT SINGLE-CHIP MICROCONTROLLER WITH DEDICATED HARDWARE FOR DIGITAL TUNING SYSTEM

µPD17P709A
AC Characteristics (TA = –40 to +85°C, VDD = 5 V ±10%)
Parameter
Operating frequency
SIO0 input frequency
Symbol
Conditions
fIN1
VCOL pin,
Sine-wave input VIN = 0.15Vp-p
MF mode
Sine-wave input VIN = 0.1Vp-p
fIN2 VCOL pin, HF mode, sine-wave input
VIN = 0.1Vp-p^Note
fIN3 VCOH pin, VHF mode, sine-wave input
VIN = 0.1Vp-p^Note
fIN4 AMIFC pin, sine-wave input
VIN = 0.15Vp-p
fIN5 FMIFC pin, FMIF count mode, sine-wave input
VIN = 0.20Vp-p
fIN6 FMIFC pin, AMIF count mode, sine-wave input
VIN = 0.15Vp-p
fIN7
External clock
MIN.
0.8
0.5
10
60
0.4
10
0.4
TYP.
MAX.
3
3
40
130
0.5
11
0.5
1
Unit
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
SIO1 input frequency
fIN8
External clock
0.7 MHz
Note
The condition of sine-wave input VIN = 0.1Vp-p is the rated value when the µPD17P709A is operating alone.
Where influence of noise must be taken into consideration, operation under input amplitude conditions of
VIN = 0.15Vp-p is recommended.
A/D Converter Characteristics (TA = –40 to +85°C, VDD = 5 V ±10%)
Parameter
Symbol
A/D conversion total error
8 bits
A/D conversion total error
8 bits
Conditions
MIN. TYP. MAX. Unit
±3.0 LSB
TA = 0 to 85°C
±2.5 LSB
Reference Characteristics (TA = +25°C, VDD = 5.0 V)
Parameter
Supply current
Symbol
Conditions
IDD3 When CPU and PLL are operating with sine-wave
input to VCOH pin
(fIN = 130 MHz, VIN = 0.3Vp-p)
MIN. TYP. MAX. Unit
6.0 12.0 mA
DC Programming Characteristics (TA = 25°C, VDD = 6.0 ±0.25 V, VPP = 12.5 ±0.5 V)
Parameter
Symbol
Conditions
MIN.
TYP.
MAX.
Unit
Input voltage, high
Input voltage, low
Input leakage current
Output voltage, high
Output voltage, low
VDD supply current
VPP supply current
VIH1
Pins other than CLK
VIH2
CLK
VIL1
Pins other than CLK
VIL2
CLK
ILI
VIN = VIL or VIH
VOH
IOH = –1 mA
VOL
IOL = 1 mA
IDD
IPP
MD0 = VIL, MD1 = VIH
0.7VDD
VDD – 0.5
0
0
VDD – 1.0
VDD
V
VDD
V
0.2VDD
V
0.4
V
10
µA
V
1.0
V
30
mA
30
mA
Cautions 1. Ensure that VPP does not exceed +13.5 V including overshoot.
2. VDD must be applied before VPP, and cut after VPP.
28
Data Sheet U15723EJ1V0DS