PLC810PG Datasheet, PDF (18/26 Pages) Power Integrations, Inc. – Continuous Mode PFC & LLC Controller Continuous Mode PFC & LLC Controller

PLC810PG
Absolute Maximum Ratings
Table 1 lists the absolute maximum ratings. Stress beyond
these limits is likely to cause permanent damage to the
PLC810PG. Exposure to conditions above recommended
operating limits may effect performance and reliability. Normal
ESD handling precautions are recommended.
Absolute Maximum Ratings
Junction temperature..................................... -40 °C to +125 °C
Storage temperature...................................... -65 °C to +150 °C
Theta_JA.......................................................................... 35 °C/W
Continuous supply voltage (VCC, VCCL)............... -0.3 V to 15 V
LLC voltage (HB pin)........................................... -0.3 V to 600 V
LLC high side floating supply voltage
(VCCHB pin with respect to HB pin)...................... -0.3 V to V_CCL
LLC high side floating output voltage
(GATEH)....................... ............................. V_HB-0.3 to V_VCCHB+0.3
LLC low side output voltage (GATEL)...........-0.3 V to VCCL+0.3
GNDP to GND............. ........................................ -0.3 V to +0.3
GND to GNDL ............. ........................................ -0.3 V to +0.3
Power dissipation...........................................................700 mW
Terminal Voltage With Respect To GND
3.3 V Tolerant pins....................................... -0.3 V to V_REF+0.3 V ISL and ISP pins, max current....................................... -100 mA
ISL and ISP pins......................................... -0.65 V to V_REF+0.3 V I_FMAX.............................. .................................................. 120 mA
Table 1. Absolute Maximum Ratings.
DC operating characteristics
Table 2 lists the minimum, typical, and maximum DC operating
voltages and currents for all inputs and outputs of PLC810PG.
Negative currents flow out of the IC, positive currents flow into
the IC. The DC operating characteristics are for a junction
temperature of -10 °C to 125 °C and VCC = 12 V, unless
otherwise noted. All voltages are relative to GNDP, GNDL or
GND (0 V). The pin names that are designated by VCC refer to
VCC, VCCL and VCCHB. The voltages on this pins are
respectively to GNDP/GND, GNDL and HB.
Parameter
Symbol Pin
Notes
Min
Typ
Max Units
Power Supply Current
Startup Current
I_CCOFF
Inhibit Current
I_CCINHIBIT
VCC
VCCL
VCC
VCCL
VCC/VCCL = UVLO -
VCCHB = 0
V(FBP) < INH (inhibit state)
VCC/VCCL = 12 V
VCCHB = 0
60
120
mA
1.1
2
mA
0.7
1.5
mA
1.1
2
Operating Current
Leakage Current
VCC PFC and LLC operating 100 kHz
I_CCON
/ 50% duty cycle, GATE outputs
(VCCL +
unloaded, No Load on V_REF
VCCHB) ^{VCC/VCCL/VCCHB = 12 V}
3.0
4.5
mA
7
9
ISP, ISL,
I_OZ
FBP,
VCOMP,
0 < V_IN < V_REF. Device in
UVLO state.
-10
FMAX
10
mA
Leakage Current
I_OZ
ISP
V_IN = -0.48 V
-10
-800
mA
18
Rev. F 08/09
www.powerint.com