TCC-202 Datasheet, PDF (11/23 Pages) ON Semiconductor – Two-Output PTIC Control IC

TCC−202
Table 10. MIPI RFFE INTERFACE SPECIFICATION
(T_A = −30 to +85°C; 2.3 V < VDDA < 5.5 V; 1.62 < VIO < 1.98 V; unless otherwise specified)
Parameter
Description
Min
Typ
Max
Unit
F_SCLK
Clock Full−Speed
Frequency
0.032
−
26
MHz
T_SCLK
Clock Full−Speed Period
0.038
−
32
ms
T_SCLKIH
CLK Input High Time
11.25
−
−
ns
T_SCLKIL
CLK Input Low Time
11.25
−
−
ns
TD_SETUP
Write DATA Setup Time
−1
−
1
ns
TD_HOLD
Write DATA Hold Time
−5
−
5
ns
T_{READ_ACCESS} Read DATA valid from
CLK rising edge
−
−
7.11
ns
T_{READ_ACCESS} Read DATA valid from
CLK rising edge
−
−
9.11
ns
Comments
Full−Speed Operation:
1.62 V< VIO < 1.98 V
Full−Speed Operation:
1.62 V< VIO < 1.98 V
Full−Speed
Full−Speed
Full−Speed
Full−Speed
Full Speed at VIO = 1.80 V,
= 25°C and max 15 pF load on
DATA pin
Full Speed at VIO = 1.80 V,
= 25°C and max 50 pF load on
DATA pin
The control IC contains thirteen 8−bit registers. Register content is described in Table 11. Some additional registers
implemented as provision, are not described in this document.
Table 11. MIPI RFFE ADDRESS MAP
Register
Address
Description
Purpose
Access
Type
Size (bits)
0x00
DAC Configuration (Enable Mask)
High voltage output enable mask
Write
7
0x01
Turbo Register DAC A, B
Turbo−charge configuration DAC A, B (Note 2)
Write
8
0x02
DAC A Register
OUT A value [6:0]
Write
8
0x03
DAC B Register
OUT B value [6:0]
Write
8
0x09
Wake Up
Wake−Up Controls
Write
8
0x10
Boost Voltage (VHV)
Settings for the boost high voltage
Write
8
0x12
Turbo−Charge Delay DAC A, B
Turbo−charge delay steps
DAC A, B
Write
8
0x13
Turbo−Charge Delay DAC A, B
Turbo−charge delay, multiplication
DAC A, B
Write
8
0x1A
MIPI−RFFE STATUS
Detect MIPI protocol errors
Read/Write
8
0x1B
RFFE Group SID
MIPI RFFE group slave
Write
8
0x1C
Power Mode and Trigger Register
Power mode & trigger control
Write
8
0x1D
Product ID Register
Product number (Notes 3 and 5)
Write
8
0x1E
Manufacturer ID Register
MN (10 bits long)
Manufacturer ID[7:0] (Note 4)
Write
8
0x1F
Unique Slave Identifier Register (USID) Spare [7:6]
[5,4] = Manufacturer ID [9:8]
Write
8
0x2C
Glide Timer Settings
[6:5] Turbo and Glide control / [4:0] Glide Timer
Write
8
setting / Need extended write for this register
2. The details for configuration of Turbo mode should be ascertained from the Programming Guide, available from ON Semiconductor.
3. The two least significant bits from Product ID register are programmed in OTP during manufacture. The other six bits of Product ID are
hardcoded in ASIC.
4. Manufacture ID is hardcoded in ASIC, and mapped in a READ−only register, not programmed in OTP.
5. TCC−202 supports WRITE access to Product ID, only in respect to comply with MIPI RFFE specification 6.8.3, Programmable USID”, of
MIPI Alliance Specification for RF Front−End Control Interface (RFFE) Version 1.00.00 26 July 2011.
www.onsemi.com
11