|
PIC16F1934_11 Datasheet, PDF (18/472 Pages) Microchip Technology – 28/40/44-Pin Flash-Based, 8-Bit CMOS Microcontrollers | |||
|
◁ |
PIC16(L)F1934/6/7
TABLE 1-2: PIC16(L)F1934/6/7 PINOUT DESCRIPTION (CONTINUED)
Name
Function
Input Output
Type Type
Description
RA6/OSC2/CLKOUT/VCAP(2)/
SEG1
RA6
OSC2
TTL CMOS General purpose I/O.
â XTAL Crystal/Resonator (LP, XT, HS modes).
CLKOUT â CMOS FOSC/4 output.
VCAP Power Power Filter capacitor for Voltage Regulator (PIC16F1934/6/7 only).
SEG1
â
AN LCD Analog output.
RA7/OSC1/CLKIN/SEG2
RA7
TTL CMOS General purpose I/O.
OSC1 XTAL â Crystal/Resonator (LP, XT, HS modes).
CLKIN CMOS â External clock input (EC mode).
SEG2
â
AN LCD Analog output.
RB0/AN12/CPS0/CCP4/SRI/INT/ RB0
SEG0
TTL CMOS General purpose I/O. Individually controlled interrupt-on-change.
Individually enabled pull-up.
AN12
AN
â A/D Channel 12 input.
CPS0
AN
â Capacitive sensing input 0.
CCP4
ST CMOS Capture/Compare/PWM4.
SRI
â
ST SR Latch input.
INT
ST
â External interrupt.
SEG0
â
AN LCD analog output.
RB1/AN10/C12IN3-/CPS1/P1C/
VLCD1
RB1
TTL CMOS General purpose I/O. Individually controlled interrupt-on-change.
Individually enabled pull-up.
AN10
AN
â A/D Channel 10 input.
C12IN3- AN
â Comparator C1 or C2 negative input.
CPS1
AN
â Capacitive sensing input 1.
P1C
â CMOS PWM output.
VLCD1 AN
â LCD analog input.
RB2/AN8/CPS2/P1B/VLCD2
RB2
TTL CMOS General purpose I/O. Individually controlled interrupt-on-change.
Individually enabled pull-up.
AN8
AN
â A/D Channel 8 input.
CPS2
AN
â Capacitive sensing input 2.
P1B
â CMOS PWM output.
VLCD2 AN
â LCD analog input.
RB3/AN9/C12IN2-/CPS3/
CCP2(1)/P2A(1)/VLCD3
RB3
TTL CMOS General purpose I/O. Individually controlled interrupt-on-change.
Individually enabled pull-up.
AN9
AN
â A/D Channel 9 input.
C12IN2- AN
â Comparator C1 or C2 negative input.
CPS3
AN
â Capacitive sensing input 3.
CCP2
ST CMOS Capture/Compare/PWM2.
P2A
â CMOS PWM output.
VLCD3 AN
â LCD analog input.
Legend: AN = Analog input or output CMOS = CMOS compatible input or output
OD = Open Drain
TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I2C⢠= Schmitt Trigger input with I2C
HV = High Voltage
XTAL = Crystal
levels
Note 1: Pin function is selectable via the APFCON register.
2: PIC16F1934/6/7 devices only.
3: PIC16(L)F1936 devices only.
4: PORTD is available on PIC16(L)F1934/7 devices only.
5: RE<2:0> are available on PIC16(L)F1934/7 devices only.
DS41364E-page 18
ï£ 2008-2011 Microchip Technology Inc.
|
▷ |