LTC3838-1_15 Datasheet, PDF (23/52 Pages) Linear Technology – Dual, Fast, Accurate Step-Down DC/DC Controller with Dual Differential Output Sensing

LTC3838-1
APPLICATIONS INFORMATION
LTC3838-1
SENSE⁺
SENSE^–
INDUCTOR
L DCR
L/DCR = (R1||R2) C1
R1
V_OUT
C_OUT
C1
R2
(OPT)
38381 F05
If V_SENSE(MAX) is within the maximum sense voltage (30mV
or 60mV typical) of the LTC3838-1 as set by the V_RNG pin,
then the RC filter only needs R1. If V_SENSE(MAX) is higher,
then R2 may be used to scale down the maximum sense
voltage so that it falls within range.
The maximum power loss in R1 is related to duty cycle,
and will occur in continuous mode at the maximum input
voltage:
C1 NEAR SENSE PINS
Figure 5. DCR Current Sensing
( ) _{PLOSS (R1) =}
V_IN(MAX) – V_OUT
R1
• V_OUT
two resistors (R1 and R2) and one capacitor (C1) as shown
in Figure 5. If the external (R1||R2) • C1 time constant is
chosen to be exactly equal to the L/DCR time constant, the
voltage drop across the external capacitor is equal to the
voltage drop across the inductor DCR multiplied by R2/
(R1 + R2). Therefore, R2 may be used to scale the voltage
across the sense terminals when the DCR is greater than
the target sense resistance. C1 is usually selected in the
range of 0.01µF to 0.47µF. This forces R1||R2 to around
2k to 4k, reducing error that might have been caused by
the SENSE pins’ input bias currents.
Resistor R1 should be placed close to the switching node,
to prevent noise from coupling into sensitive small-signal
nodes. Capacitor C1 should be placed close to the IC pins.
The first step in designing DCR current sensing is to
determine the DCR of the inductor. Where provided, use
the manufacturer’s maximum value, usually given at 25°C.
Increase this value to account for the temperature coef-
ficient of resistance, which is approximately 0.4%/°C. A
conservative value for inductor temperature T_L is 100°C.
The DCR of the inductor can also be measured using a good
RLC meter, but the DCR tolerance is not always the same
and varies with temperature; consult the manufacturers’
data sheets for detailed information.
From the DCR value, V_SENSE(MAX) is easily calculated as:
V_SENSE(MAX) = DCR_MAX(25°C)
( ) ^{•1+ 0.4% T}L(MAX) ^{– 25°C }
• ^{}I_{OUT(MAX )}
–
∆I_L
2


Ensure that R1 has a power rating higher than this value.
If high efficiency is necessary at light loads, consider this
power loss when deciding whether to use DCR sensing or
R_SENSE sensing. Light load power loss can be modestly
higher with a DCR network than with a sense resistor due
to the extra switching losses incurred through R1. How-
ever, DCR sensing eliminates a sense resistor, reduces
conduction losses and provides higher efficiency at heavy
loads. Peak efficiency is about the same with either method.
To maintain a good signal-to-noise ratio for the current
sense signal, start with a ∆V_SENSE of 10mV. For a DCR
sensing application, the actual ripple voltage will be de-
termined by:
∆V_SENSE
=
V_IN – V_OUT
R1• C1
•
V_OUT
V_IN • f
Power MOSFET Selection
Two external N-channel power MOSFETs must be selected
for each channel of the LTC3838-1 controller: one for the
top (main) switch and one for the bottom (synchronous)
switch. The gate drive levels are set by the DRV_CC voltage.
This voltage is typically 5.3V. Pay close attention to the
BV_DSS specification for the MOSFETs as well; most of the
logic-level MOSFETs are limited to 30V or less.
Selection criteria for the power MOSFETs include the on-
resistance, R_DS(ON), Miller capacitance, C_MILLER, input
voltage and maximum output current. Miller capacitance,
C_MILLER, can be approximated from the gate charge curve
usually provided on the MOSFET manufacturers’ data
sheet. C_MILLER is equal to the increase in gate charge along
the horizontal axis while the curve is approximately flat
38381f
For more information www.linear.com3838-1
23