ISL12022M_10 Datasheet, PDF (24/31 Pages) Intersil Corporation – Low Power RTC with Battery Backed SRAM,Integrated ±5ppm Temperature Compensation and Auto Daylight Saving

ISL12022M
TABLE 24. XT0 VALUES
XT<4:0>
TURNOVER
TEMPERATURE
01111
32.5
01110
32.0
01101
31.5
01100
31
01011
30.5
01010
30
01001
29.5
01000
29.0
00111
28.5
00110
28.0
00101
27.5
00100
27.0
00011
26.5
00010
26.0
00001
25.5
00000
25.0
10000
25.0
10001
24.5
10010
24.0
10011
23.5
10100
23.0
10101
22.5
10110
22.0
10111
21.5
11000
21.0
11001
20.5
11010
20.0
11011
19.5
11100
19.0
11101
18.5
11110
18.0
11111
17.5
ALPHA Hot Register (ALPHAH)
TABLE 25. ALPHAH REGISTER
ADDR 7
6
5
4
3
2
1
0
2Dh D ALP_H6 ALP_H5 ALP_H4 ALP_H3 ALP_H2 ALP_H1 ALP_H0
The ALPHA Hot variable is 7 bits and is defined as the
temperature coefficient of Crystal from the XT0 value to
+85°C (both Alpha Hot and Alpha Cold must be
programmed to provide full temperature
compensation). It is normally given in units of ppm/°C²,
with a typical value of -0.034. Like the ALPHA Cold
version, a scaled version of the absolute value of this
coefficient is used in order to get an integer value.
Therefore, ALP_H <7:0> is defined as the (|Actual
Alpha Hot Value| x 2048) and converted to binary. For
example, a crystal with Alpha Hot of -0.034ppm/°C² is
first scaled (|2048*(-0.034)| = 70d) and then
converted to a binary number of 01000110b.
The practical range of Actual ALPHAH values is from
-0.020 to -0.060.
The ISL12022M has a preset ALPHAH value
corresponding to the crystal in the module. This value is
recalled on initial power-up and is preset in device
production. It is READ ONLY and cannot be
overwritten by the user.
User Registers (Accessed by
Using Slave Address
1010111x)
Addresses [00h to 7Fh]
These registers are 128 bytes of battery-backed user
SRAM. The separate I²C slave address must be used to
read and write to these registers.
I²C Serial Interface
The ISL12022M supports a bi-directional bus oriented
protocol. The protocol defines any device that sends data
onto the bus as a transmitter and the receiving device as
the receiver. The device controlling the transfer is the
master and the device being controlled is the slave. The
master always initiates data transfers and provides the
clock for both transmit and receive operations.
Therefore, the ISL12022M operates as a slave device in
all applications.
All communication over the I²C interface is conducted by
sending the MSB of each byte of data first.
Protocol Conventions
Data states on the SDA line can change only during SCL
LOW periods. SDA state changes during SCL HIGH are
reserved for indicating START and STOP conditions (see
Figure 15). On power-up of the ISL12022M, the SDA pin
is in the input mode.
All I²C interface operations must begin with a START
condition, which is a HIGH to LOW transition of SDA
while SCL is HIGH. The ISL12022M continuously
monitors the SDA and SCL lines for the START condition
and does not respond to any command until this
condition is met (see Figure 15). A START condition is
ignored during the power-up sequence.
All I²C interface operations must be terminated by a
STOP condition, which is a LOW to HIGH transition of
SDA while SCL is HIGH (see Figure 15). A STOP condition
at the end of a read operation or at the end of a write
operation to memory only places the device in its
standby mode.
24
FN6668.7
June 4, 2010