E1962B Datasheet, PDF (4/26 Pages) Agilent(Hewlett-Packard) – cdma2000/IS-95/AMPS Mobile Test Application

CW RF generator
Frequency
Available frequency range: 292 to 2700 Mhz
Specified frequency ranges:
421 to 494 MHz
800 to 960 MHz
1700 to 2000 MHz
Accuracy and stability: same as listed under FM RF generator
Test signal: CW, AM (56% depth with 20 kHz rate), or DSB-SC
(carrier + upper side-band spaced 20 kHz apart); requires
approximately 3 seconds to switch between test signal
selections
Amplitude
Available output level range: −127 to −10 dBm
Specified output level range: −116 to −15 dBm
Absolute output level accuracy: < ±1.0 dB, typically < ±0.5 dB
(level accuracy at RF generator output levels > −30 dBm may
be degraded by simultaneous reception and transmission when
applied Tx power is > 32 dBm)
VSWR at RF IN/OUT: < 1.14:1, 400 to 1000 MHz
Nominal ambient test signal level accuracy: < ±1.1 dB
FM and SAT signal generation
FM rate range: 100 Hz to 20 kHz
FM deviation range: 0 to 20 kHz for combined SAT, internal and
external deviation
Residual FM: < 7 Hz rms in a CCITT bandwidth
Internal FM accuracy: < ±(3.5% + residual FM) at a 1 kHz rate
External FM accuracy: < ±(5% + residual FM) at a 1 kHz rate
FM flatness: < ±5% relative to a 1 kHz rate
FM distortion (THD plus noise): < 0.5% for > 4 kHz deviation at a
1 kHz rate in a CCITT bandwidth
External FM input sensitivity: 20 kHz deviation per V
Maximum external FM input level: 1 V peak
SAT frequencies: 5970, 6000, or 6030 Hz
SAT deviation: fixed at 2 kHz
FM rate resolution: typically 5 Hz
FM deviation resolution: typically 5 Hz
Audio generator
Frequency
Operating range: 100 Hz to 20 kHz, typically 1 Hz to 20 kHz
Accuracy: same as timebase reference
Frequency resolution: typically 0.1 Hz
FM RF generator
Frequency
Frequency range: 800 to 960 Mhz
Accuracy and stability: same as timebase reference
CW frequency switching speed: typically < 10 ms to be within
< 0.1 ppm of final frequency
Setting resolution: typically 1 Hz
Amplitude
Output level range: −116 to −15 dBm
Absolute output level accuracy: < ±1.0 dB, typically < ±0.5 dB
(level accuracy at RF generator output levels > −30 dBm may
be degraded by simultaneous reception and transmission when
applied Tx power is > 32 dBm)
RF IN/OUT reverse power: +37 dBm peak (5 W peak)
VSWR at RF IN/OUT: < 1.14:1, 400 MHz to 1000 MHz
Output level repeatability (returning to the same frequency and
level): typically < ±0.1 dB
Output level setting resolution: typically 0.1 dB
Output level switching time: typically < 50 ms to be within 0.1 dB
of final level
Output level (from AUDIO OUTPUT connector)
Ranges: 0 to 1 V peak, 1 to 9 V peak (into > 600 Ω)
Accuracy: < ±(1.5% of setting + resolution) when output is DC
coupled
Distortion: < 0.1% for 0.2 to 9 V peak into > 600 Ω
Coupling mode: selectable as DC or AC (5 µF in series with
output)
Maximum output current: typically 100 mA peak into 8 Ω
Output impedance: typically < 1.5 Ω at 1 kHz when output is DC
coupled
DC offset (when output is DC coupled):
typically < 1 mV peak for 0 to 1 V peak
typically < 10 mV peak for 1 to 9 V peak
Output level resolution: typically < 0.5 mV for 0 to 1 V peak
output, < 5.0 mV for 1 to 9 V peak output
Spectral purity
Harmonics: −25 dBc for levels < −17 dBm
Subharmonics: < −40 dBc
Non-harmonics:
< −55 dBc for 100 kHz to < 1500 kHz offsets from carrier
< −68 dBc for > 1500 kHz offsets from carrier
typically < −55 dBc for 3 kHz to < 100 kHz offsets
typically < −53 dBc for line-related non-harmonics
Spurious due to receiver LO leakage: spurious at 105 ±2.5 MHz
below expected transmitter frequency and its second harmonic
is typically < −50 dBm
4