E1962B Datasheet, PDF (21/26 Pages) Agilent(Hewlett-Packard) – cdma2000/IS-95/AMPS Mobile Test Application

Maximum/minimum power measurement
Input frequency ranges:
411 to 420 MHz
450 to 484 MHz
824 to 934 MHz
1700 to 1980 MHz
Measurement method: performs this sequence:
• Sets the test set source to a user-specified value for the
maximum power measurement
• Ranges the receiver to the expected power
• Sends all up power control bits
• Uses the average power meter to measure the maximum
power
• Sets the test set source to a user-specified value for the
minimum power measurement
• Ranges the receiver to the expected power
• Sends all down power control bits
• Uses the channel power meter to measure the minimum
power
• Returns the test set to the same state before the
measurement was initiated
Measurement data capture period: 1.25 ms
Maximum input level: +37 dBm/1.23 MHz peak (5 W peak)
Measurement range:
Maximum power measurement: −10 to +30 dBm; usable from
−10 to −20 dBm with reduced accuracy (peak detector only)
Minimum power measurement: −61 to +30 dBm; usable to
< −69 dBm/1.23 MHz with reduced accuracy
Measurement level ranging: auto for the maximum power
measurement, and either auto or manual for the minimum
power measurement
Measurement accuracy:
Maximum power measurement: same as the average power
measurement accuracy
Minimum power measurement: same as the channel power
measurement accuracy
Measurement settings: maximum power measurement cell
power, maximum power measurement F-FCH level, maximum
power measurement F-Pilot level, minimum power
measurement cell power, minimum power measurement F-FCH
level, minimum power measurement F-Pilot level
Measurement result: the measured maximum power and
minimum power
Concurrency capabilities: none
Calibrate function: uses the channel power calibration function
Multi-tone audio measurement
Multi-tone analyzer supported service options: SO1, SO3 (EVRC
vocoder), SO17, and SO32768 (13 k vocoder)
Multi-tone audio measurement mode: downlink audio (base
station to mobile station) or uplink audio (mobile station to
base station)
Multi-tone analyzer 0 dB reference mode: relative or absolute
Multi-tone analyzer 0 dB reference tone (relative mode): tone 0
through 20
Multi-tone analyzer downlink reference level (absolute mode):
1 mV to 5.000 V
Multi-tone analyzer uplink reference level (absolute mode): 0.1
to 100%
Multi-tone analyzer expected audio input peak voltage
(downlink mode): 1 mV to 20.000 V
Multi-tone analyzer device setting time: 10 to 1000 ms
Multi-tone analyzer SINAD/distortion state (in the 1 tone mode
only): selectable on or off
Multi-tone analyzer downlink encoder setting: 0 to 100 frames
Multi-tone downlink generator frequency presets:
Narrow: 300 Hz, 400 Hz, 500 Hz, 600 Hz, 700 Hz, 800 Hz, 900 Hz,
1 kHz, 1.1 kHz, 1.2 kHz, 1.3 kHz, 1.4 kHz, 1.6 kHz, 1.8 kHz,
2.0 kHz, 2.2 kHz, 2.4 kHz, 2.6 kHz, 2.8 kHz, and 3.0 kHz
Normal: 300 Hz, 600 Hz, 800 Hz, 1 kHz, 1.2 kHz, 1.6 kHz, 2.0 kHz,
2.4 kHz, and 3.0 kHz
Wide: 100 Hz, 200 Hz, 300 Hz, 400 Hz, 500 Hz, 600 Hz, 700 Hz,
800 Hz, 900 Hz, 1 kHz, 1.2 kHz, 1.4 kHz, 1.6 kHz, 1.8 kHz, 2.0 kHz,
2.4 kHz, 2.8 kHz, 3.0 kHz, 3.3 kHz, and 3.6 kHz
Multi-tone downlink generator frequency level: 10, 30, or 50% of
total level
Multi-tone uplink generator frequency presets: same as
downlink presets or selectable for up to 20 tones; user
frequency range from 10 Hz to 4.0 kHz
Multi-tone uplink generator frequency level: specified total rms
voltage range from 20 mV to 1.42 V
Multi-tone analyzer measurement results (SINAD/distortion
mode off): graphical display of up to 20 tones with level
(frequency response)
Multi-tone analyzer measurement results (SINAD/distortion
mode on): tone audio level, tone audio frequency, tone SINAD,
and tone distortion
Multi-tone analyzer measurement limits: upper and lower tone
pass/fail limit for each active tone; range of −100 to +100 dB
for each limit
Concurrency capabilities: none
21