E1962B Datasheet, PDF (13/26 Pages) Agilent(Hewlett-Packard) – cdma2000/IS-95/AMPS Mobile Test Application

Option E1962B-403 CDMA authentication
Adds support for IS-95/cdma2000 active cell authentication. Does
not support encryption.
CDMA authentication
Functionality: provides basic authentication capabilities for call
processing; does not support encryption.
Authentication commands: unique challenge and SSD update
Global challenge: on or off
Authentication user parameters: A-key (decimal), RAND (hex),
RANDU (hex), and RANDSSD (hex)
Global challenge results: AUTHU expected value, AUTHU
received value and pass/fail result; RANDC expected value,
RANDC received value and pass/fail result; COUNT (call
history); AUTH_MODE
Unique challenge results: AUTHU expected value, AUTHU
received value, and pass/fail result
SSD update results: pass/fail result
IS-2000 test mode functionality
Resident formats: IS-2000 SR1
Cell overhead channels:
F-Pilot: with user-settable PN offset
F-Sync: with real-time long code and system time update and
updates for user entered parameters
F-Paging: with real-time overhead messages
F-QPCH: with all indicators on or all off
Protocol stack: limited to IS-2000 revision 0 with addendum sync
channel message and paging channel overhead messages
Base station parameters: NID, SID, country code (MCC), network
code (MNC), paging rate, CDG esc mode, F-QPCH state, F-QPCH
relative level, F-QPCH data bits (all on or all off), and reverse
link traffic pilot gain
Call control (“one button commands”): none
Access parameters: none
Registration support: none
Service option support: none
Handoff support: none
R-Access channel: not supported
Chip rate: 1.2288 Mcps
Supported radio configuration combinations:
forward RC 1 + reverse RC 1
forward RC 2 + reverse RC 2
forward RC 3 + reverse RC 3
forward RC 4 + reverse RC 3
forward RC 5 + reverse RC 4
Channel coding: convolutional or turbo on all rates with the
exception that turbo coding is not available on RC3 at 9.6 kbps,
RC4 at 9.6 kbps, or RC5 at 14.4 kbps per IS-2000
Traffic data source: PRBS (CCITT 2¹⁵−1 pattern)
Forward FCH data rate:
RC1: 1.2, 2.4, 4.8, 9.6 kbps
RC2: 1.8, 3.6, 7.2, 14.4 kbps
RC3: 1.5, 2.7, 4.8, 9.6 kbps
RC4: 1.5, 2.7, 4.8, 9.6 kbps
RC5: 1.8, 3.6, 7.2, 14.4 kbps
Forward SCH support: one supplemental channel
F-SCH data rate:
RC3: 9.6, 19.2, 38.4, 76.8, or 153.6 kbps
RC4: 9.6, 19.2, 38.4, 76.8, or 153.6 kbps
RC5: 14.4, 28.8, 57.6, 115.2, or 230.4 kbps
Power control groups: 16 per frame
Reverse link closed loop support: transmits bits only (no reverse
link demodulation)
Reverse link closed loop bit rate: fixed to 800 per second
Reverse link closed loop power control modes:
alternating – alternating 0 and 1 power bits
alt 20 up/down – alternating 20 up/20 down bits
all up
all down
Reverse link closed loop power control transient: user start
function that interrupts the current reverse link closed loop
power control mode and substitutes the user-defined number
and direction of closed loop power control bits; once the
transient is sent, the closed loop power control reverts to the
original state
Reverse link closed loop power control transient modes: up,
down, and up-down-up
Transient number of steps: 1 to 400
Forward link power support: none
Mobile station identification: user entry of ESN (hex); entry of all
“F” hex data results in using a zero long code mask on the
source
13