MA28140 Datasheet, PDF (47/72 Pages) Dynex Semiconductor – Packet Telecommand Decoder

MA28140
8. ELECTRICAL CHARACTERISTICS AND RATINGS
8.1 DC PARAMETERS
Parameter
Supply Voltage
Input Voltage
Current Through Any Pin
Operating Temperature
Storage Temperature
Min
Max
Units ^{Note: Stresses above those listed may cause permanent}
damage to the device. This is a stress rating only and
-0.5
7
V
functional operation of the device at these conditions, or at
any other condition above those indicated in the operations
-0.3 V_DD+0.3
V
section of this specification, is not implied. Exposure to
-20
+20
mA ^{absolute maximum rating conditions for extended periods}
may affect device reliability.
-55
125
°C
-65
150
°C
Table 7: Absolute Maximum Ratings
Symbol Parameter
Conditions
Min.
Typ.
Max. Units
V_DD
Supply Voltage
-
4.5
5.0
5.5
V
V_IHC
CMOS input high voltage
-
0.8 V_DD
-
V_DD
V
V_ILC
CMOS input low voltage
-
V_SS
-
0.2 V_DD
V
V_IHT
TTL input high voltage
-
2
-
-
V
V_ILT
TTL input low voltage
-
-
-
0.8
V
V_OH
Output high voltage
I_OH = -3.2mA
0.9 V_DD
-
-
V
V_OL
Output high voltage
I_OL = 5.0mA
-
-
0.1 V_DD
V
I_PDL
Input Pull-down current
V_DD = 5.5V, V_IN = V_SS
-30
-
30
µA
I_PDH
Input Pull-down current
V_DD = 5.5V, V_IN = V_DD
-30
-
150
µA
I_PUL
Input Pull-up current
V_DD = 5.5V, V_IN = V_SS
-150
-
30
µA
I_PUH
Input Pull-up current
V_DD = 5.5V, V_IN = V_DD
-30
-
30
µA
I_L
Input leakage current
V_DD = 5.5V, V_IN = V_SS or V_DD
-10
-
10
µA
I_OZL
Output leakage current
V_DD = 5.5V, V_OUT = V_SS
-50
-
50
µA
I_OZH
Output leakage current
V_DD = 5.5V, V_OUT = V_DD
-50
-
50
µA
I_OPDL
Output Pull-down current
V_DD = 5.5V, V_IN = V_SS
-50
-
50
µA
I_OPDH
Output Pull-down current
V_DD = 5.5V, V_IN = V_DD
-50
-
150
µA
I_DD1
Static Power supply Current
V_DD = 5.5V
-
0.5
20
mA
I_DD2
Dynamic Power supply Current f = 4MHz, V_DD = 5.5V
-
20
40
mA
Notes: 1. V_DD = 5V ±10% over full temperature range.
2. Total dose radiation not exceeding 10⁵ Rads(Si).
3. Mil-Std-883, method 5005, subgroups 1, 2, 3.
4. All outputs are suitable for TTL/CMOS drive.
5. Electro-Static Discharge protection is provided for all pins.
6. Internal pull-up or pull-down resistors should not be relied upon for proper operation and/or termination of input levels
under all operating conditions without prior consultation with Dynex Semiconductor.
7. Input and output leakage measurements are guaranteed but not tested at -55°C.
Table 8: DC Characteristics
Symbol Parameter
Conditions
Min.
Typ.
Max.
C_IN
C_OUT
Input Capacitance
Output Capacitance
V_I = 0V
V_I/O = 0V
-
3
5
-
5
7
NOTE 1: T_A = 25˚C and f = 1MHz. Data obtained by characterisation or analysis; not routinely measured.
Table 9: Capacitance
Units
pF
pF
47/72