|
HMC701LP6CE Datasheet, PDF (33/40 Pages) Hittite Microwave Corporation – 8 GHz 16-Bit Fractional-N Synthesizer | |||
|
◁ |
v09.1112
HMC701LP6CE
8 GHz 16-BIT FRACTIONAL-N PLL
Table 29. Reg 12h Delta Sigma Modulator Register
Bit
Type
Name
0
R/W dsm_ref_clk_select
1
R/W dsm_invert_clk_sd3
2
R/W dsm_invert_clk_rph
3
R/W dsm_integer_mode
Default
0
1
0
0
Description
use reference instead of divider Program 0
invert Îâ clk
inverts the ref clock phase
1- enables Integer Mode, bypasses the Îâ
modulator, leaves it running
see also dsm_rstb Reg01h<13> to disable the
modulator
4
R/W Reserved
0
5
R/W Reserved
6
R/W dsm_xref_sin_select
7
R/W dsm_autoseed
9:8
R/W dsm_order
13:10
17:14
R/W dsm_quant_max
R/W dsm_quant_min
0
0
when xref is selected specifies that the sine
source is used
1
automatic seed load when changing the frac
part, uses value in seed
Delta-Sigma Modulator configuration:
00-1st order 01-2nd order 10-3rd order Feedback
2
11-3rd order Feedforward
Use either 10 or 11. For Sweeper operation use
11 only.
Do not use 1st or 2nd order (for test only)
3h
max value allowed out of Îâ modulator quantizer
limits are +7 to -8, typ ±3 or ±4 Program 3h
Ch
min value allowed out of Îâ modulator quantizer
limits are +7 to -8, typ ±3 or ±4 Program Ch
Table 30. Reg 14h CW Sweep Control Register
The maximum sweep range is limited to 255 x Fxtal/R. Delta-Sigma Modulator mode should be Feed
Forward when using Sweep feature (Register 12h Bits [9:8] = 11.
Bit
Type
Name
Default
Description
0
R/W clear_ovf_undf
0
asynchronous clear for ovf/undf flags
1
R/W ramp_enable
0
Ramp En/rstb
1= enables the CW Ramp Function
2
R/W ramp_trigg
Write always triggers ramps if bit <2> = 0, if bit
0
<2> = 1, Ramp will not trigger, bit <2> must be
reset to 0 first
3
R/W ramp_repeat_en
Ramp Repeat Seq enable
0
1= enables autotrigger of ramps
0 = ramp_trigg starts each ramp
4
R/W ramp_startdir_dn
Ramp start direction
0
1= Start with Ramp Down
0= Start with Ramp Up
5
R/W ramp_trig_ext_en
0
Enable hardware trigger on GPO3 pin
6
R/W ramp_singlestep
0
Ramp single step, advances the ramp to the next
step, and holds frequency
7
R/W ramp_singledir
0
Ramps in one direction only with hop to start at
end of ramp
33
IrrliniecgfseohFpntrsomsoenoasrftiisibtohpingilrirrtdyafiuncpirstnaeeairdsts,ihesbesduydmtehimebaldtypivmlbiAcPeyaanyAhtariorlynooenagslnauoolDrgetneofD:rdvtoheim9cevteri7cwoistes8issiuspe-fso2lbeura.ne5idtSlcis0eepevure-esca3deoinf,i3yctnroadop4triaboe3ftenoersrnastascn:oucyrbuHFjipernaaacfirtttteiexnttnoig:attecner9mhdiga7ehMnrnte8gstlseii-aoco2bwffrlAie5ptohn.a0oawtHuelo-tonag3wntsvoDe3otveiecr7eveori3C,.ctheNnesooor. rpOFOPoorhrndraoenetpTierroei:ccnO7eh8,,nn12od--30lleoi2lngiA9veye-l4rWpay7h,at0yaa0w,nâ¢PRdw.OOowtor.ad.Bdephorl,iaxtocCtn9ietl1hein0oe.e6rcld,maoeNtmrswosf:rwowArwondo.aa,dlno,MagMloAADge.00cv21oic0m8e62s24,-9In10c.6,
Trademarks and registered trademarks aArepthpelpircopaetrityoonf thSeiur rpesppeoctrivte: oPwhneorsn. e: 978-250-33A4p3plicoartioanpSpusp@pohrti:tPtihteo.nceo: 1m-800-ANALOG-D
|
▷ |