XC4VLX15_08 Datasheet, PDF (3/56 Pages) Xilinx, Inc – Virtex-4 FPGA Data Sheet

R
Virtex-4 FPGA Data Sheet: DC and Switching Characteristics
Table 2: Recommended Operating Conditions (Continued)
Symbol
Description
Min
Max Units
AVCCAUXRX⁽⁶⁾ Auxiliary receive supply voltage relative to GNDA
Commercial
1.14
Industrial
1.14
1.26
V
1.26
V
AVCCAUXTX⁽⁶⁾ Auxiliary transmit supply voltage relative to GNDA
Commercial
1.14
Industrial
1.14
1.26
V
1.26
V
AVCCAUXMGT Auxiliary management supply voltage relative to GNDA
Commercial
Industrial
2.375
2.375
2.625
V
2.625
V
V_TRX ⁽⁷⁾
Terminal receive supply voltage relative to GND
Commercial
0.25
Industrial
0.25
2.5
V
2.5
V
V_TTX
Terminal transmit supply voltage relative to GND
Commercial
1.14
Industrial
1.14
1.575
V
1.575
V
Notes:
1. Configuration data is retained even if V_CCO drops to 0V.
2. V_BATT is required only when using bitstream encryption. If battery is not used, connect V_BATT to either ground or V_CCAUX.
3. For 3.3V I/O operation, refer to the Virtex-4 FPGA User Guide.
4. Includes V_CCO of 1.2V, 1.5V, 1.8V, 2.5V, and 3.3V
5. The configuration output supply voltage V_{CC_CONFIG} is also known as V_{CCO_0}
6. IMPORTANT! All unused RocketIO transceivers must be connected to power and GND. When using RocketIO transceivers, refer to the power filtering
section of the Virtex-4 RocketIO Multi-Gigabit Transceiver User Guide. Unused transceivers must be powered by an appropriate voltage level source.
Passive filtering must meet the requirements discussed in the Virtex-4 RocketIO Multi-Gigabit Transceiver User Guide.
7. Internal AC coupling is enabled.
Table 3: DC Characteristics Over Recommended Operating Conditions
Symbol
Description
Data Rate
(Gb/s)
Min Typ Max
V_DRINT
Data retention V_CCINT voltage
(below which configuration data might be lost)
0.9
V_DRI
Data retention V_CCAUX voltage
(below which configuration data might be lost)
2.0
I_REF
I_L
C_IN
I_RPU(1)
I_RPD(1)
I_BATT(1)
V_REF current per pin
Input or output leakage current per pin (sample-tested)
Input capacitance (sample-tested)
Pad pull-up (when selected) @ V_IN = 0V, V_CCO = 3.3V
Pad pull-up (when selected) @ V_IN = 0V, V_CCO = 3.0V
Pad pull-up (when selected) @ V_IN = 0V, V_CCO = 2.5V
Pad pull-up (when selected) @ V_IN = 0V, V_CCO = 1.8V
Pad pull-up (when selected) @ V_IN = 0V, V_CCO = 1.5V
Pad pull-down (when selected) @ V_IN = V_CCO
Battery supply current
10
10
10
5
200
5
125
5
120
5
60
5
40
5
100
75 100
6.5
292 427
5.0
302 485
I_CCAUXRX(2) Operating AVCCAUXRX supply current
4.25
3.125
291 446
279 382
1.25/2.5
263 351
1.25 Digital RX
314 432
Units
V
V
µA
µA
pF
µA
µA
µA
µA
µA
µA
nA
mA
mA
mA
mA
mA
mA
DS302 (v3.2) April 10, 2008
www.xilinx.com
Product Specification
3