CC1350_16 Datasheet, PDF (8/61 Pages) Texas Instruments – SimpleLink Ultra-Low-Power Dual-Band Wireless MCU

CC1350
SWRS183A – JUNE 2016 – REVISED NOVEMBER 2016
www.ti.com
4.2 Signal Descriptions – RSM Package
Table 4-1. Signal Descriptions – RSM Package
PIN
NAME
NO.
DCDC_SW
18
DCOUPL
12
TYPE
Power
Power
DESCRIPTION
Output from internal DC-DC⁽¹⁾
1.27-V regulated digital-supply decoupling capacitor⁽²⁾
DIO_0
8
Digital I/O
GPIO, Sensor Controller, high-drive capability
DIO_1
9
Digital I/O
GPIO, Sensor Controller, high-drive capability
DIO_2
10
Digital I/O
GPIO, Sensor Controller, high-drive capability
DIO_3
15
Digital I/O
GPIO, high-drive capability, JTAG_TDO
DIO_4
16
Digital I/O
GPIO, high-drive capability, JTAG_TDI
DIO_5
22
Digital or analog I/O GPIO, Sensor Controller, analog
DIO_6
23
Digital or analog I/O GPIO, Sensor Controller, analog
DIO_7
24
Digital or analog I/O GPIO, Sensor Controller, analog
DIO_8
25
Digital or analog I/O GPIO, Sensor Controller, analog
DIO_9
26
Digital or analog I/O GPIO, Sensor Controller, analog
EGP
–
Power
Ground; exposed ground pad
JTAG_TMSC
13
Digital I/O
JTAG TMSC
JTAG_TCKC
14
Digital I/O
JTAG TCKC
RESET_N
21
Digital input
Reset, active low. No internal pullup.
RF_N
2
RF I/O
Negative RF input signal to LNA during RX
Negative RF output signal from PA during TX
RF_P
1
RF I/O
Positive RF input signal to LNA during RX
Positive RF output signal from PA during TX
RX_TX
VDDS
VDDS2
4
RF I/O
Optional bias pin for the RF LNA
27
Power
1.8-V to 3.8-V main chip supply⁽¹⁾
11
Power
1.8-V to 3.8-V GPIO supply⁽¹⁾
VDDS_DCDC
19
VDDR
28
VDDR_RF
32
Power
Power
Power
1.8-V to 3.8-V DC-DC supply
1.7-V to 1.95-V supply, connect to output of internal DC-DC ⁽²⁾⁽³⁾
1.7-V to 1.95-V supply, connect to output of internal DC-DC ⁽²⁾⁽⁴⁾
VSS
3, 7, 17,
20, 29
Power
Ground
X32K_Q1
5
Analog I/O
32-kHz crystal oscillator pin 1
X32K_Q2
6
Analog I/O
32-kHz crystal oscillator pin 2
X24M_N
30
Analog I/O
24-MHz crystal oscillator pin 1
X24M_P
31
Analog I/O
24-MHz crystal oscillator pin 2
(1) See the technical reference manual listed in Section 8.3 for more details.
(2) Do not supply external circuitry from this pin.
(3) If internal DC-DC is not used, this pin is supplied internally from the main LDO.
(4) If internal DC-DC is not used, this pin must be connected to VDDR for supply from the main LDO.
8
Terminal Configuration and Functions
Submit Documentation Feedback
Product Folder Links: CC1350
Copyright © 2016, Texas Instruments Incorporated