CC1350_16 Datasheet, PDF (20/61 Pages) Texas Instruments – SimpleLink Ultra-Low-Power Dual-Band Wireless MCU

CC1350
SWRS183A – JUNE 2016 – REVISED NOVEMBER 2016
www.ti.com
5.9 Transmit (TX) Parameters, 431 MHz to 527 MHz
Measured on the Texas Instruments CC1310EM-7XD-4251 reference design with T_c = 25°C, V_DDS = 3.0 V, DC-DC enabled,
f_RF = 433.92 MHz, unless otherwise noted. All measurements are performed at the antenna input with a combined RX and TX
path.
PARAMETER
TEST CONDITIONS
MIN
TYP MAX UNIT
Maximum output power, boost mode
VDDR = 1.95 V
Minimum VDDS for boost mode is 2.1 V
15
dBm
Maximum output power
14
dBm
30 MHz to 1 GHz
Spurious emissions
(excluding harmonics)⁽¹⁾
1 GHz to 12.75 GHz
Transmitting +10 dBm, 433 MHz
Inside ETSI restricted bands
Transmitting +10 dBm, 433 MHz
Outside ETSI restricted bands
Transmitting +10 dBm, 433 MHz
Outside ETSI restricted bands, measured
in 1-MHz bandwidth (ETSI)
Transmitting +10 dBm, 433 MHz
Inside ETSI restricted bands, measured in
1-MHz bandwidth (ETSI)
<–63
<–39
<–52
<–58
dBm
(1) Suitable for systems targeting compliance with EN 300 220, EN 54-25, EN 303 204, FCC CFR47 Part 15, ARIB STD-T108.
5.10 1-Mbps GFSK (Bluetooth low energy) – RX
Measured on the TI CC1350_7XD-Dual Band reference design with T_c = 25°C, V_DDS = 3.0 V, f_RF = 2440 MHz, unless
otherwise noted. All tests with Bluetooth low energy PHY (1 Mbps), 37-byte payload unless otherwise noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
Differential mode. Measured at the CC1350_7XD-
Receiver sensitivity
Dual Band SMA connector,
–87
37-byte payload BER = 10^–3
Differential mode. Measured at the CC1350_7XD-
Receiver sensitivity
Dual Band SMA connector,
–86
255-byte payload BER = 10^–3
Receiver saturation
Differential mode. Measured at the CC1350_7XD-
Dual Band SMA connector, BER = 10^–3
0
Difference between the incoming carrier frequency
Frequency error tolerance
and the internally generated carrier frequency.
–350
350
Input signal 10 dB above sensitivity limit
Difference between incoming data rate and the
Data rate error tolerance
internally generated data rate. Input signal 10 dB
–750
750
above sensitivity limit
Co-channel rejection⁽¹⁾
Wanted signal at –67 dBm, modulated interferer in
channel, BER = 10^–3
–6
Selectivity, ±1 MHz⁽¹⁾
Wanted signal at –67 dBm, modulated interferer at
±1 MHz, BER = 10^–3
7 / 4 ⁽²⁾
Selectivity, +2 MHz⁽¹⁾
Wanted signal at –67 dBm, modulated interferer at
+2 MHz, BER = 10^–3
38
Selectivity, ±3 MHz⁽¹⁾
Wanted signal at –67 dBm, modulated interferer at
±3 MHz, BER = 10^–3.
Note that –3 MHz is –1 MHz from the image
frequency.
36 / 41⁽²⁾
Selectivity, ±4 MHz⁽¹⁾
Wanted signal at –67 dBm, modulated interferer at
±4 MHz, BER = 10^–3
39 / 38⁽²⁾
Selectivity, ±5 MHz⁽¹⁾
Wanted signal at –67 dBm, modulated interferer at
±5 MHz, BER = 10^–3
35 / 39⁽²⁾
Selectivity, ±6 MHz⁽¹⁾
Wanted signal at –67 dBm, modulated interferer at
≥ ±6 MHz, BER = 10^–3
42 / 37⁽²⁾
Selectivity, ±15 MHz or more⁽¹⁾
Wanted signal at –67 dBm, modulated interferer at
≥ ±15 MHz or more, BER = 10^–3
55
UNIT
dBm
dBm
dBm
kHz
ppm
dB
dB
dB
dB
dB
dB
dB
dB
(1) Numbers given as I/C dB.
(2) X / Y, where X is +N MHz and Y is –N MHz.
20
Specifications
Submit Documentation Feedback
Product Folder Links: CC1350
Copyright © 2016, Texas Instruments Incorporated