CC1350_16 Datasheet, PDF (21/61 Pages) Texas Instruments – SimpleLink Ultra-Low-Power Dual-Band Wireless MCU

www.ti.com
CC1350
SWRS183A – JUNE 2016 – REVISED NOVEMBER 2016
1-Mbps GFSK (Bluetooth low energy) – RX (continued)
Measured on the TI CC1350_7XD-Dual Band reference design with T_c = 25°C, V_DDS = 3.0 V, f_RF = 2440 MHz, unless
otherwise noted. All tests with Bluetooth low energy PHY (1 Mbps), 37-byte payload unless otherwise noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
Selectivity, Image frequency
(image compensation enabled, Wanted signal at –67 dBm, modulated interferer at
the image compensation is
image frequency, BER = 10^–3
37
calibrated in production)⁽¹⁾
Selectivity, Image frequency
±1 MHz⁽¹⁾
Out-of-band blocking⁽³⁾
Wanted signal at –67 dBm, modulated interferer at
±1 MHz from image (–3 MHz and –1 MHz from
wanted) frequency, BER = 10^–3
30 MHz to 2000 MHz
4 / 41⁽²⁾
–25
Out-of-band blocking
2003 MHz to 2399 MHz
>–20
Out-of-band blocking
2484 MHz to 2997 MHz
>–20
Out-of-band blocking
3000 MHz to 12.75 GHz
>–30
Wanted signal at 2402 MHz, –64 dBm. Two
Intermodulation
interferers at 2405 and 2408 MHz, respectively, at
–30
the given power level
Conducted measurement in a 50-Ω single-ended
Spurious emissions,
30 to 1000 MHz
load. Suitable for systems targeting compliance
with EN 300 328, EN 300 440 class 2, FCC
–72
CFR47, Part 15 and ARIB STD-T-66
Conducted measurement in a 50-Ω single-ended
Spurious emissions,
1 to 12.75 GHz
load. Suitable for systems targeting compliance
with EN 300 328, EN 300 440 class 2, FCC
–65
CFR47, Part 15 and ARIB STD-T-66
RSSI dynamic range
70
RSSI accuracy
±4
(3) Excluding one exception at F_wanted / 2, per Bluetooth Specification.
UNIT
dB
dB
dBm
dBm
dBm
dBm
dBm
dBm
dBm
dB
dB
5.11 1-Mbps GFSK (Bluetooth low energy) – TX
Measured on the TI CC1350_7XD-Dual Band reference design with T_c = 25°C, V_DDS = 3.0 V, f_RF = 2440 MHz, unless
otherwise noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
Output power, boost mode
Differential mode, delivered to a single-ended 50-Ω load
through a balun.
VDDR = 1.95 V
Minimum VDDS for boost mode is 2.1 V.
9
dBm
Output power
Differential mode, delivered to a single-ended 50-Ω load
through a balun.
5
dBm
Output power, lowest setting Delivered to a single-ended 50-Ω load through a balun
–21
dBm
f < 1 GHz, outside restricted bands
–59
Spurious emission conducted ^{f < 1 GHz, restricted bands ETSI}
measurement ⁽¹⁾
f < 1 GHz, restricted bands FCC
–55
dBm
–61
f > 1 GHz, including harmonics
–47
(1) Suitable for systems targeting compliance with worldwide radio-frequency regulations ETSI EN 300 328 and EN 300 440 Class 2
(Europe), FCC CFR47 Part 15 (US), and ARIB STD-T66 (Japan).
Copyright © 2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: CC1350
Specifications
21