CC1350_16 Datasheet, PDF (17/61 Pages) Texas Instruments – SimpleLink Ultra-Low-Power Dual-Band Wireless MCU

www.ti.com
CC1350
SWRS183A – JUNE 2016 – REVISED NOVEMBER 2016
Receive (RX) Parameters, 861 MHz to 1054 MHz (continued)
Measured on the Texas Instruments CC1350_7XD-Dual Band reference design with T_c = 25°C, V_DDS = 3.0 V, DC-DC
enabled, f_RF = 868 MHz, unless otherwise noted. All measurements are performed at the antenna input with a combined RX
and TX path.
PARAMETER
TEST CONDITIONS
MIN
TYP MAX UNIT
Spurious emissions 1 GHz to 13 GHz
(VCO leakage at 3.5 GHz) and 30 MHz
to 1 GHz
Radiated emissions measured according to
ETSI EN 300 220
–70
dBm
Image rejection (image compensation
enabled, the image compensation is
calibrated in production)
Wanted signal 3 dB above sensitivity limit. 50 kbps,
GFSK, 25-kHz deviation, 100-kHz RX bandwidth (same
modulation format as IEEE 802.15.4g mandatory
mode), BER = 10^–2
44
dB
RSSI dynamic range
50 kbps, GFSK, 25-kHz deviation, 100-kHz RX
bandwidth (same modulation format as IEEE 802.15.4g
mandatory mode). Starting from the sensitivity limit. This
range will give an accuracy of ±2 dB.
95
dB
RSSI accuracy
50 kbps, GFSK, 25-kHz deviation, 100-kHz RX
bandwidth (same modulation format as IEEE 802.15.4g
mandatory mode). Starting from the sensitivity limit
across the given dynamic range.
±2
dB
Receiver sensitivity, long-range mode
625 bps
10 ksym/s, GFSK, 5-kHz deviation, FEC (half rate),
DSSS = 8, 40-kHz RX bandwidth, BER = 10^–2.
868 MHz and 915 MHz.
–124
dBm
Selectivity, ±100 kHz, long-range mode
625 bps
Wanted signal 3 dB above sensitivity limit. 10 ksym/s,
GFSK, 5-kHz deviation, FEC (half rate), DSSS = 8,
40-kHz RX bandwidth, BER = 10^–2
56, 56
dB
Selectivity, ±200 kHz, long-range mode
625 bps
Wanted signal 3 dB above sensitivity limit. 10 ksym/s,
GFSK, 5-kHz deviation, FEC (half rate), DSSS = 8,
40-kHz RX bandwidth, BER = 10^–2
62, 65
dB
Blocking ±1 MHz, long-range mode
625 bps
Wanted signal 3 dB above sensitivity limit. 10 ksym/s,
GFSK, 5-kHz deviation, FEC (half rate), DSSS = 8,
40-kHz RX bandwidth, BER = 10^–2
73, 77
dB
Blocking ±2 MHz, long-range mode
625 bps
Wanted signal 3 dB above sensitivity limit. 10 ksym/s,
GFSK, 5-kHz deviation, FEC (half rate), DSSS = 8,
40-kHz RX bandwidth, BER = 10^–2
79, 79
dB
Blocking ±10 MHz, long-range mode
625 bps
Receiver sensitivity, OOK 4.8 kbps
Wanted signal 3 dB above sensitivity limit. 10 ksym/s,
GFSK, 5-kHz deviation, FEC (half rate), DSSS = 8,
40-kHz RX bandwidth, BER = 10^–2
4.8 kbps, OOK, 40-kHz RX bandwidth, BER = 10^–2
868 MHz and 915 MHz. Measured on CC1310EM-7XD-
7793.
91, 91
–115
dB
dBm
5.7 Receive (RX) Parameters, 431 MHz to 527 MHz
Measured on the Texas Instruments CC1350_7XD-Dual Band reference design with T_c = 25°C, V_DDS = 3.0 V, DC-DC
enabled, f_RF = 433.92 MHz, unless otherwise noted. All measurements are performed at the antenna input with a combined
RX and TX path.
PARAMETER
TEST CONDITIONS
MIN
TYP MAX UNIT
Receiver sensitivity, 50 kbps
50 kbps, GFSK, 25-kHz deviation, 100-kHz RX
bandwidth (same modulation format as IEEE 802.15.4g
mandatory mode), BER = 10^–2
–110
dBm
Receiver saturation
50 kbps, GFSK, 25-kHz deviation, 100-kHz RX
bandwidth (same modulation format as IEEE 802.15.4g
mandatory mode), BER = 10^–2
10
dBm
Selectivity, ±200 kHz, 50 kbps
Wanted signal 3 dB above sensitivity limit. 50 kbps,
GFSK, 25-kHz deviation, 100-kHz RX bandwidth (same
modulation format as IEEE 802.15.4g mandatory
mode), BER = 10^–2
44, 47
dB
Selectivity, ±400 kHz, 50 kbps
Wanted signal 3 dB above sensitivity limit. 50 kbps,
GFSK, 25-kHz deviation, 100-kHz RX bandwidth (same
modulation format as IEEE 802.15.4g mandatory
mode), BER = 10^–2
42, 50
dB
Copyright © 2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: CC1350
Specifications
17