CC3220MOD_017 Datasheet, PDF (36/100 Pages) Texas Instruments – SimpleLink Wi-Fi CERTIFIED Wireless MCU Modules

CC3220MOD, CC3220MODA
SWRS206B – MARCH 2017 – REVISED AUGUST 2017
www.ti.com
5.5 Current Consumption (CC3220MODSF and CC3220MODASF)
T_A = 25°C, V_BAT = 3.6 V
PARAMETER
TEST CONDITIONS^{(1) (2)}
MIN TYP MAX UNIT
TX power level = 0
286
1 DSSS
TX power level = 4
202
TX
MCU ACTIVE
NWP ACTIVE
6 OFDM
54 OFDM
TX power level = 0
TX power level = 4
TX power level = 0
TX power level = 4
255
192
232
mA
174
RX ⁽³⁾
NWP idle connected⁽⁴⁾
1 DSSS
54 OFDM
74
74
25.2
TX power level = 0
282
1 DSSS
TX power level = 4
198
MCU SLEEP
TX
NWP ACTIVE
6 OFDM
54 OFDM
TX power level = 0
TX power level = 4
TX power level = 0
TX power level = 4
251
188
228
mA
170
RX ⁽³⁾
NWP idle connected⁽⁴⁾
1 DSSS
54 OFDM
70
70
21.2
TX power level = 0
266
1 DSSS
TX power level = 4
184
TX
NWP active
MCU LPDS
6 OFDM
54 OFDM
TX power level = 0
TX power level = 4
TX power level = 0
TX power level = 4
242
176
mA
217
154
RX ⁽³⁾
NWP LPDS⁽⁵⁾
NWP idle connected⁽⁴⁾
1 DSSS
54 OFDM
53
53
135
µA
710
µA
MCU hibernate
MCU shutdown
NWP hibernate
NWP shutdown
5
µA
1
Peak calibration current ⁽⁶⁾
V_BAT= 3.6 V
V_BAT= 3.3 V
V_BAT= 2.3 V
420
450
mA
620
(1) TX power level = 0 implies maximum power (see Figure 5-1, Figure 5-2, and Figure 5-3). TX power level = 4 implies output power
backed off approximately 4 dB.
(2) CC3220MODx and CC3220MODAx are constant, power-source systems. The active current numbers scale based on the V_BAT voltage
supplied.
(3) The RX current is measured with a 1-Mbps throughput rate.
(4) DTIM = 1
(5) The LPDS number of reported is with retention of 256KB of MCU SRAM. The CC3220MODx and CC3220MODAx modules can be
configured to retain 0KB, 64KB, 128KB, 192KB, or 256KB of SRAM in LPDS. Each 64-KB block of MCU retained SRAM increases
LPDS current by 4 μA.
(6) The complete calibration can take up to 17 mJ of energy from the battery over a time of 24 ms. In default mode, calibration is performed
sparingly, and typically occurs when re-enabling the NWP and when the temperature has changed by more than 20°C. There are two
additional calibration modes that may be used to reduced or completely eliminate the calibration event. For further details, see CC3x20
SimpleLink™ Wi-Fi^® and Internet of Things Network Processor Programmer's Guide.
36
Specifications
Copyright © 2017, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: CC3220MOD CC3220MODA