OMAPL137CZKBT3 Datasheet, PDF (140/222 Pages) Texas Instruments – OMAP-L137 Low-Power Applications Processor

OMAP-L137
SPRS563G – SEPTEMBER 2008 – REVISED JUNE 2014
www.ti.com
Table 6-66. Additional⁽¹⁾ SPI1 Master Timings, 4-Pin Enable Option^{(2) (3)}
No.
17 t_{d(EN A_SPC)M}
18 t_{d(SPC_ENA)M}
PARAMETER
MIN
Polarity = 0, Phase = 0,
to SPI1_CLK rising
Delay from slave assertion of
SPI1_ENA active to first SPI1_CLK
from master.⁽⁴⁾
Polarity = 0, Phase = 1,
to SPI1_CLK rising
Polarity = 1, Phase = 0,
to SPI1_CLK falling
Polarity = 1, Phase = 1,
to SPI1_CLK falling
Polarity = 0, Phase = 0,
from SPI1_CLK falling
Max delay for slave to deassert
SPI1_ENA after final SPI1_CLK edge
to ensure master does not begin the
next transfer.⁽⁵⁾
Polarity = 0, Phase = 1,
from SPI1_CLK falling
Polarity = 1, Phase = 0,
from SPI1_CLK rising
Polarity = 1, Phase = 1,
from SPI1_CLK rising
MAX
UNIT
3P + 3
0.5t_c(SPC)M + 3P + 3
ns
3P + 3
0.5t_c(SPC)M + 3P + 3
0.5t_c(SPC)M + P + 5
P+5
ns
0.5t_c(SPC)M + P + 5
P+5
(1) These parameters are in addition to the general timings for SPI master modes (Table 6-64).
(2) P = SYSCLK2 period
(3) Figure shows only Polarity = 0, Phase = 0 as an example. Table gives parameters for all four master clocking modes.
(4) In the case where the master SPI is ready with new data before SPI1_ENA assertion.
(5) In the case where the master SPI is ready with new data before SPI1_ENA deassertion.
Table 6-67. Additional⁽¹⁾ SPI1 Master Timings, 4-Pin Chip Select Option^{(2) (3)}
No.
19 t_{d(SCS_SPC)M}
20 t_{d(SPC_SCS)M}
PARAMATER
Delay from SPI1_SCS active to first
SPI1_CLK^{(4) (5)}
Delay from final SPI1_CLK edge to
master deasserting SPI1_SCS ^{(6) (7)}
Polarity = 0, Phase = 0,
to SPI1_CLK rising
Polarity = 0, Phase = 1,
to SPI1_CLK rising
Polarity = 1, Phase = 0,
to SPI1_CLK falling
Polarity = 1, Phase = 1,
to SPI1_CLK falling
Polarity = 0, Phase = 0,
from SPI1_CLK falling
Polarity = 0, Phase = 1,
from SPI1_CLK falling
Polarity = 1, Phase = 0,
from SPI1_CLK rising
Polarity = 1, Phase = 1,
from SPI1_CLK rising
MIN
MAX UNIT
2P -5
0.5t_c(SPC)M + 2P -5
ns
2P -5
0.5t_c(SPC)M + 2P -5
0.5t_c(SPC)M + P - 3
P-3
ns
0.5t_c(SPC)M + P -3
P-3
(1) These parameters are in addition to the general timings for SPI master modes (Table 6-64).
(2) P = SYSCLK2 period
(3) Figure shows only Polarity = 0, Phase = 0 as an example. Table gives parameters for all four master clocking modes.
(4) In the case where the master SPI is ready with new data before SPI1_SCS assertion.
(5) This delay can be increased under software control by the register bit field SPIDELAY.C2TDELAY[4:0].
(6) Except for modes when SPIDAT1.CSHOLD is enabled and there is additional data to transmit. In this case, SPI1_SCS will remain
asserted.
(7) This delay can be increased under software control by the register bit field SPIDELAY.T2CDELAY[4:0].
140 Peripheral Information and Electrical Specifications
Copyright © 2008–2014, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: OMAP-L137