BQ24262_15 Datasheet, PDF (33/56 Pages) Texas Instruments – bq2426x 3-A, 30-V, Host-Controlled Single-Input, Single-Cell Switched-Mode Li-Ion Battery Charger With Power-Path Management and USB-OTG Support

Not Recommended for New Designs : bq24260, bq24261
www.ti.com
bq24260, bq24261, bq24261M, bq24262
SLUSBU4D – DECEMBER 2013 – REVISED APRIL 2015
9.6.3 Control/Battery Voltage Register (READ/WRITE)
Memory location: 02, Reset state: 0001 0100 (BQ24260/1/1M), 1000 1100 (bq24262)
Figure 22. bq24260/1/1M Control/Battery Voltage Register
B7(MSB)
B6
B5
B4
B3
B2
B1
B0(LSB)
1
0
0
0
1
1
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Figure 23. bq24262 Control/Battery Voltage Register
B7(MSB)
B6
B5
B4
B3
B2
B1
B0(LSB)
0
0
0
1
0
1
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 4. Control/Battery Voltage Register Field Descriptions
BIT
B7(MSB)
B6
B5
B4
B3
B2
B1
B0(LSB)
FIELD
V_BREG5
V_BREG4
V_BREG3
V_BREG2
V_BREG1
V_BREG0
MOD_FREQ1
MOD_FREQ0
TYPE
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
DESCRIPTION
Battery Regulation Voltage: 640 mV (default 0)
Battery Regulation Voltage: 320 mV (default 0)
Battery Regulation Voltage: 160 mV (default 0)
Battery Regulation Voltage: 80 mV (default 1)
Battery Regulation Voltage: 40 mV (default 0)
Battery Regulation Voltage: 20 mV (default 1)
Modify Switching Frequency Target –
00 – No Change to Nominal Frequency Target
01 – +10% Change to Nominal Frequency
10 – -10% Change to Nominal Frequency
11 – NA (default 00)
V_BREG Bits (Battery Regulation Threshold setting)
Use V_BREG bits to set the battery regulation threshold. The VBATREG is calculated using the following
equation:
indent V_BATREG = 3.5 V + V_BREGCODE × 20 mV
The charge voltage range is 3.5 V to 4.44 V with the offset of 3.5 V and step of 20 mV. The default setting
is 3.6 V for the bq24260 and bq24261 and bq24261M. The default setting is 4.2 V for the bq24262. If a
value greater than 4.44 V is written, the setting goes to 4.44 V. It is recommended to set V_BATREG above
V_MINSYS.
MOD_FREQx Bits (Frequency Modification)
The MOD_FREQx bits are used to change the switching frequency by ±10%. This is used for applications
where the 1.5MHz switching frequency noise interferes with other device operation. The frequency may
be modified by ±10% of the nominal frequency.
Copyright © 2013–2015, Texas Instruments Incorporated
Submit Documentation Feedback
33
Product Folder Links: bq24260 bq24261 bq24261M bq24262