|
M37221M6_03 Datasheet, PDF (53/62 Pages) Renesas Technology Corp – SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER | |||
|
◁ |
MITSUBISHI MICROCOMPUTERS
M37221M6-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
ABSOLUTE MAXIMUM RATINGS
Symbol
Parameter
Conditions
Ratings
Unit
VCC
Power source voltage VCC
All voltages are based
â0.3 to 6
V
VI
Input voltage
CNVSS
on VSS.
Output transistors are
â0.3 to 6
V
VI
Input voltage
P00âP07,P10âP17, P20âP27,
cut off.
â0.3 to VCC + 0.3
V
P30âP34, OSC1, XIN, HSYNC,
VSYNC, RESET
VO
Output voltage
P06, P07, P10âP17, P20âP27,
P30âP32, R, G, B, OUT1, D-A,
XOUT, OSC2
â0.3 to VCC + 0.3
V
VO
Output voltage
P00âP05
â0.3 to 13
V
IOH
Circuit current
R, G, B, OUT1, P10âP17,
P20âP27, P30, P31, D-A
0 to 1 (Note 1)
mA
IOL1
Circuit current
R, G, B, OUT1, P06, P07, P10,
P15âP17, P20âP23, P30âP32,
D-A
0 to 2 (Note 2)
mA
IOL2
Circuit current
P11âP14
0 to 6 (Note 2)
mA
IOL3
Circuit current
P00âP05
0 to 1 (Note 2)
mA
IOL4
Circuit current
P24âP27
0 to 10 (Note 3)
mA
Pd
Power dissipation
Ta = 25 °C
550
mW
Topr
Operating temperature
â10 to 70
°C
Tstg
Storage temperature
â40 to 125
°C
RECOMMENDED OPERATING CONDITIONS (Ta = â10 °C to 70 °C, VCC = 5 V ± 10 %, unless otherwise noted)
Symbol
VCC
VSS
VIH1
VIH2
VIL1
VIL2
VIL3
IOH
IOL1
IOL2
IOL3
IOL4
fCPU
fCRT
fhs1
fhs2
fhs3
Parameter
Power source voltage (Note 4), During CPU, CRT operation
Power source voltage
âHâ input voltage
P00âP07,P10âP17, P20âP27, P30âP34,
SIN, SCLK, HSYNC, VSYNC, RESET, XIN,
OSC1, TIM2, TIM3, INT1, INT2, INT3
âHâ input voltage
SCL1, SCL2, SDA1, SDA2
(When using I2C-BUS)
âLâ input voltage
P00âP07,P10âP17, P20âP27, P30âP34
âLâ input voltage
SCL1, SCL2, SDA1, SDA2
(When using I2C-BUS)
âLâ input voltage
HSYNC, VSYNC, RESET, TIM2, TIM3, INT1,
INT2, INT3, XIN, OSC1, SIN, SCLK
âHâ average output current (Note 1) R, G, B, OUT1, D-A, P10âP17, P20âP27,
P30, P31
âLâ average output current (Note 2) R, G, B, OUT1, D-A, P06, P07, P10,
P15âP17, P20âP27, P30âP32
âLâ average output current (Note 2) P11âP14
âLâ average output current (Note 2) P00âP05
âLâ average output current (Note 3) P24âP27
Oscillation frequency (for CPU operation) (Note 5) XIN
Oscillation frequency (for CRT display) (Note 5)
OSC1
Input frequency
TIM2, TIM3
Input frequency
SCLK
Input frequency
SCL1, SCL2
Min.
4.5
0
0.8VCC
0.7VCC
0
0
0
7.9
5.0
Limits
Typ.
5.0
0
8.0
Unit
Max.
5.5
V
0
V
VCC
V
VCC
V
0.4 VCC V
0.3 VCC V
0.2 VCC V
1
mA
2
mA
6
mA
1
mA
10
mA
8.1
MHz
8.0
MHz
100
kHz
1
MHz
400
kHz
Notes 1: The total current that flows out of the IC must be 20 mA (max.).
2: The total input current to IC (IOL1 + IOL2 + IOL3) must be 30 mA or less.
3: The total average input current for ports P24âP27 to IC must be 20 mA or less.
4: Connect 0.1 µF or more capacitor externally across the power source pins VCCâVSS so as to reduce power source noise. Also connect
0.1 µF or more capacitor externally across the pins VCCâCNVSS.
5: Use a quartz-crystal oscillator or a ceramic resonator for the CPU oscillation circuit.
52
|
▷ |