M16C62A Datasheet, PDF (130/242 Pages) Mitsubishi Electric Semiconductor – SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER

A-D Converter
Mitsubishi microcomputers
M16C / 62A Group (80-pin)
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
A-D control register 0 (Note 1)
b7 b6 b5 b4 b3 b2 b1 b0
Symbol
ADCON0
Address When reset
03D616 00000XXX2
Bit symbol
CH0
CH1
CH2
MD0
MD1
TRG
Bit name
Analog input pin select bit
A-D operation mode
select bit 0
Trigger select bit
Function
b2 b1 b0
0 0 0 : AN0 is selected
0 0 1 : AN1 is selected
0 1 0 : AN2 is selected
0 1 1 : AN3 is selected
1 0 0 : AN4 is selected
1 0 1 : AN5 is selected
1 1 0 : AN6 is selected
1 1 1 : AN7 is selected
b4 b3
0 0 : One-shot mode
0 1 : Repeat mode
1 0 : Single sweep mode
1 1 : Repeat sweep mode 0
Repeat sweep mode 1
0 : Software trigger
1 : ADTRG trigger
RW
(Note 2)
(Note 2)
ADST
A-D conversion start flag 0 : A-D conversion disabled
1 : A-D conversion started
CKS0 ^{Frequency select bit 0}
0 : fAD/4 is selected
1 : fAD/2 is selected
Note 1: If the A-D control register is rewritten during A-D conversion, the conversion result is
indeterminate.
Note 2: When changing A-D operation mode, set analog input pin again.
A-D control register 1 (Note)
b7 b6 b5 b4 b3 b2 b1 b0
Symbol
ADCON1
Address
03D716
When reset
0016
Bit symbol
Bit name
A-D sweep pin select bit
SCAN0
Function
When single sweep and repeat sweep
mode 0 are selected
b1 b0
0 0 : AN0, AN1 (2 pins)
0 1 : AN0 to AN3 (4 pins)
1 0 : AN0 to AN5 (6 pins)
1 1 : AN0 to AN7 (8 pins)
RW
SCAN1
MD2
A-D operation mode
select bit 1
When repeat sweep mode 1 is selected
b1 b0
0 0 : AN0 (1 pin)
0 1 : AN0, AN1 (2 pins)
1 0 : AN0 to AN2 (3 pins)
1 1 : AN0 to AN3 (4 pins)
0 : Any mode other than repeat sweep
mode 1
1 : Repeat sweep mode 1
BITS
8/10-bit mode select bit
0 : 8-bit mode
1 : 10-bit mode
CKS1 ^{Frequency select bit 1}
0 : fAD/2 or fAD/4 is selected
1 : fAD is selected
VCUT
Vref connect bit
0 : Vref not connected
1 : Vref connected
OPA0
OPA1
External op-amp
connection mode bit
b7 b6
0 0 : ANEX0 and ANEX1 are not used
0 1 : ANEX0 input is A-D converted
1 0 : ANEX1 input is A-D converted
1 1 : External op-amp connection mode
Note: If the A-D control register is rewritten during A-D conversion, the conversion result is
indeterminate.
Figure 1.15.2. A-D converter-related registers (1)
129