HYS72T32000HR Datasheet, PDF (5/67 Pages) Qimonda AG – 240-Pin Registered DDR2 SDRAM Modules

Internet Data Sheet
HYS72T[32/64]0xxHR–[2.5/3/3S/3.7/5]–A
Registered DDR2 SDRAM Modules
1.2
Description
The QIMONDA HYS72T[32/64]0xxHR–[2.5/3/3S/3.7/5]–A
module family are Registered DIMM modules “RDIMMs” with
30 mm height based on DDR2 technology. DIMMs are
available as ECC modules in 32M x 72 (256 MByte) and
64M x 72 (512 MByte) organization and density, intended for
mounting into 240-pin connector sockets.
The memory array is designed with 256-Mbit Double-Data-
Rate-Two (DDR2) Synchronous DRAMs. All control and
address signals are re-driven on the DIMM using register
devices and a PLL for the clock distribution. This reduces
capacitive loading to the system bus, but adds one cycle to
the SDRAM timing. Decoupling capacitors are mounted on
the PCB board. The DIMMs feature serial presence detect
based on a serial E²PROM device using the 2-pin I²C
protocol. The first 128 bytes are programmed with
configuration data and are write-protected; the second
128 bytes are available to the customer.
Product Type¹⁾
Compliance Code²⁾
TABLE 3
Ordering Information for RoHS Compliant Products
Description SDRAM Technology
PC2-6400
HYS72T32000HR–2.5–A
256 MB 1R×8 PC2–6400R–666–12–F0
1 Rank, ECC 256 Mbit (×8)
HYS72T64001HR–2.5–A
512 MB 1R×4 PC2–6400R–666–12–H0
1 Rank, ECC 256 Mbit (×4)
HYS72T64020HR–2.5–A
512 MB 2R×8 PC2–6400R–666–12–G0
2 Rank, ECC 256 Mbit (×8)
PC2-5300
HYS72T32000HR–3–A
256 MB 1R×8 PC2–5300R–444–12–F0
1 Rank, ECC 256 Mbit (×8)
HYS72T64001HR–3–A
512 MB 1R×4 PC2–5300R–444–12–H0
1 Rank, ECC 256 Mbit (×4)
HYS72T64020HR–3–A
512 MB 2R×8 PC2–5300R–444–12–G0
2 Rank, ECC 256 Mbit (×8)
HYS72T32000HR–3S–A
256 MB 1R×8 PC2–5300R–555–12–F0
1 Rank, ECC 256 Mbit (×8)
HYS72T64001HR–3S–A
512 MB 1R×4 PC2–5300R–555–12–H0
1 Rank, ECC 256 Mbit (×4)
HYS72T64020HR–3S–A
512 MB 2R×8 PC2–5300R–555–12–G0
2 Rank, ECC 256 Mbit (×8)
PC2–4200
HYS72T32000HR–3.7–A
256 MB 1R×8 PC2–4200R–444–11–F0
1 rank, ECC 256 Mbit (×8)
HYS72T64001HR–3.7–A
512 MB 1R×4 PC2–4200R–444–11–H0
1 rank, ECC 256 Mbit (×4)
HYS72T64020HR–3.7–A
512 MB 2R×8 PC2–4200R–444–11–G0
2 rank, ECC 256 Mbit (×8)
PC2-3200
HYS72T32000HR–5–A
256 MB 1R×8 PC2–3200R–333–11–F0
1 Rank, ECC 256 Mbit (×8)
HYS72T64001HR–5–A
512 MB 1R×4 PC2–3200R–333–11–H0
1 Rank, ECC 256 Mbit (×4)
HYS72T64020HR–5–A
512 MB 2R×8 PC2–3200R–333–11–G0
2 Rank, ECC 256 Mbit (×8)
1) All part numbers end with a place code, designating the silicon die revision. Example: HYS72T32000HR–5–A, indicating Rev. “A” dies are
used for DDR2 SDRAM components. For all QIMONDA DDR2 module and component nomenclature see Chapter 6 of this data sheet.
2) The Compliance Code is printed on the module label and describes the speed grade, for example “PC2–4200R–444–11–F0”, where
4200R means Registered DIMM modules with 4.26 GB/sec Module Bandwidth and “444-11” means Column Address Strobe (CAS) latency
= 4, Row Column Delay (RCD) latency = 4 and Row Precharge (RP) latency = 4 using the latest JEDEC SPD Revision 1.1 and produced
on the Raw Card “F”
Rev. 1.21, 2007-03
5
09152006-J5FK-C565