HYB25D128160C Datasheet, PDF (22/35 Pages) Qimonda AG – 128-Mbit Double-Data-Rate SDRAM

Internet Data Sheet
HYB25D128xxxC[C/E/F/T](L)
128-Mbit Double-Data-Rate SDRAM
Parameter
Symbol
TABLE 18
Electrical Characteristics and DC Operating Conditions
Values
Unit Note¹⁾ / Test Condition
Min.
Typ.
Max.
Device Supply Voltage
Device Supply Voltage
Output Supply Voltage
Output Supply Voltage
Supply Voltage, I/O Supply
Voltage
Input Reference Voltage
Input Reference Voltage
V_DD
V_DD
V_DDQ
V_DDQ
V_SS,
V_SSQ
V_REF
V_REF
I/O Termination Voltage
V_TT
(System)
Input High (Logic1) Voltage
Input Low (Logic0) Voltage
Input Voltage Level, CK and
CK Inputs
V_IH(DC)
V_IL(DC)
V_IN(DC)
Input Differential Voltage, CK V_ID(DC)
and CK Inputs
VI-Matching Pull-up Current VI_Ratio
to Pull-down Current
Input Leakage Current
I_I
2.3
2.5
2.7
V f_CK ≤ 166 MHz
2.5
2.6
2.7
V
f_CK > 166 MHz ²⁾
2.3
2.5
2.7
V
f_CK ≤ 166 MHz ³⁾
2.5
2.6
2.7
V f_CK > 166 MHz
0
—
0
V—
0.49 × V_DDQ 0.5 × V_DDQ 0.51 × V_DDQ V
V_DDQ / 2
V_DDQ / 2
V_DDQ / 2
V
– 50 mV
+ 50 mV
V_REF – 0.04 —
V_REF + 0.04 V
f_CK ≤ 166 MHz ⁴⁾
f_CK > 166 MHz
5)
V_REF + 0.15 —
–0.3
—
–0.3
—
V_DDQ + 0.3 V
—
V_REF – 0.15 V —
V_DDQ + 0.3 V
—
0.36
—
V_DDQ + 0.6 V
6)
0.71
—
1.4
—
7)
–2
—
2
µA Any input 0 V ≤ V_IN ≤ V_DD; All
other pins not under test = 0 V
8)9)
Output Leakage Current
I_OZ
–5
Output High Current, Normal I_OH
—
Strength Driver
—
5
µA DQs are disabled; 0 V ≤ V_OUT ≤
V_DDQ
—
–16.2
mA V_OUT = 1.95 V
Output Low Current, Normal I_OL
16.2
—
—
Strength Driver
mA V_OUT = 0.35 V
1) 0 °C ≤ T_A ≤ 70 °C
2) DDR400 conditions apply for all clock frequencies above 166 MHz
3) Under all conditions, V_DDQ must be less than or equal to V_DD.
4) Peak to peak AC noise on V_REF may not exceed ± 2% VREF (DC). VREF is also expected to track noise variations in V_DDQ.
5) V_TT is not applied directly to the device. V_TT is a system supply for signal termination resistors, is expected to be set equal to V_REF, and
must track variations in the DC level of V_REF.
6) V_ID is the magnitude of the difference between the input level on CK and the input level on CK.
7) The ration of the pull-up current to the pull-down current is specified for the same temperature and voltage, over the entire temperature
and voltage range, for device drain to source voltage from 0.25 to 1.0 V. For a given output, it represents the maximum difference between
pull-up and pull-down drivers due to process variation.
8) Inputs are not recognized as valid until V_REF stabilizes.
9) Values are shown per component
Rev. 1.6, 2007-02
22
03292006-U5AN-6TI1