|
TDA8757 Datasheet, PDF (27/37 Pages) NXP Semiconductors – Triple 8-bit ADC 170 Msps | |||
|
◁ |
Philips Semiconductors
TDA8757
Triple 8-bit ADC 170 Msps
Table 17: Characteristicsâ¦continued
VCCA = 4.75 V to 5.25 V (referenced to AGND); VCCD = 4.75 V to 5.25 V (referenced to DGND); VDDD = 4.75 V to 5.25 V
(referenced to VSSD); VCCO = 4.75 V to 5.25 V (referenced to OGND); AGND, DGND, OGND and VSS connected together;
Tamb = 0 to 70 °C; typical values measured at VCCA = VDDD = VCCD = VCCO = 5 V and Tamb = 25 °C; unless otherwise
speciï¬ed.
Symbol
Parameter
Conditions
Min Typ Max Unit
3W-bus
trst
reset time of the chip before
3-wire communication
â
600
â
ns
tsu
data set-up time for 3-wire
communication
â
100
â
ns
th
data hold time for 3-wire
communication
â
100
â
ns
I2C-bus [5]
VIL
LOW-level input voltage
for SCL and SDA
VIH
HIGH-level input voltage
for SCL and SDA;
VPU = 5 V
for SCL and SDA;
VPU = 3 V
fSCL
clock frequency
tBUF
time the bus must be free before
new transmission can start
â
â
3
â
0.7VDD â
0
â
4.7
â
0.3VDD V
â
V
â
100 kHz
â
µs
tHD;STA
tSU;STA
tLOW
tHIGH
tSU;DAT
tHD;DAT
tr
tf
tSU;STO
Cb
start condition hold time
start condition set-up time
LOW-level clock period
HIGH-level clock period
data set-up time
data hold time
SDA and SCL rise time
SDA and SCL fall time
stop condition set-up time
bus line capacitive loading
repeated start
fSCL = 100 kHz
fSCL = 100 kHz
4.0
â
4.7
â
4.7
â
4.0
â
250
â
0
â
â
â
â
â
4.0
â
â
â
â
µs
â
µs
â
µs
â
µs
â
ns
â
ns
1.0
µs
300 ns
â
µs
400 pF
[1] From 25 to 70 °C, the edge of the clock CKDATA has a shift of 1 phase compared to CKREF.
[2] Effective bits are obtained from a Fast Fourier Transform (FFT) treatment taking 8000 acquisition points per equivalent fundamental
period. The calculation takes into account all harmonics and noise up to half clock frequency (NYQUIST frequency).
Conversion-to-noise ratio: S/N = EB Ã 6.02 + 1.76 dB.
[3] Output data acquisition: the output data is available after the maximum sampling delay time td(s). All the timings are given for a 10 pF
capacitive load.
[4] Pulse relative to the blank level.
[5] The I2C-bus timings are given for use of the bus at a frequency of 100 kbit/s (100 kHz). This bus could be used at a frequency of
400 kbit/s (400 kHz).
9397 750 09457
Preliminary data
Rev. 07 â 28 February 2002
© Koninklijke Philips Electronics N.V. 2002. All rights reserved.
27 of 37
|
▷ |