80CL31 Datasheet, PDF (27/40 Pages) NXP Semiconductors – Low-voltage single-chip 8-bit microcontrollers

Philips Semiconductors
Low-voltage single-chip 8-bit microcontrollers
Product specification
80CL31/80CL51
2.0 RATINGS
Limiting values in accordance with the Absolute Maximum System (IEC 134)
SYMBOL
PARAMETER
V_DD
V_I
I_I, I_O
P_TOT
T_STG
T_AMB
T_J
Supply voltage (pin 40)
All input voltages
DC current into any input or output
Total power dissipation
Storage temperature range
Operating ambient temperature range
Operating junction temperature
MIN.
-0.5
-0.5
-
-
-65
-40
-
MAX.
+ 6.5
V_DD+0.5
5
300
+150
+85
125
UNIT
V
V
mA
mW
°C
°C
°C
3.0 DC CHARACTERISTICS P80CL31/P80CL51
V_SS = 0V; T_AMB = -40 to +85°C; all voltages with respect to V_SS unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
V_DD
Supply voltage
V_DD
RAM retention in power down mode
Supply current operating (Note 1, Note 4)
V_SS = 0V
1.8
-
6.0
V
1.0
–
–
V
I_DD
OSC 1 option
I_DD
OSC 2 option
I_DD
OSC 3 option
I_DD
OSC 4 option
Idle Mode (Note 2, Note 4)
f_cIk = 32 KHz; V_DD = 1.8V
T_AMB - 25°C
f_cIk = 3.58 MHz; V_DD = 3V
f_cIk = 16 MHz; V_DD = 5V
f_cIk = 16 MHz; V_DD = 5V
-
-
50
µA
-
-
2.5
mA
-
-
24
mA
-
-
26
mA
I_DD
I_DD
I_DD
I_DD
I_PD
Inputs
OSC 1 option
OSC 2 option
OSC 3 option
OSC 4 option
Power down (Note 3, Note 4)
f_cIk = 32 KHz; V_DD = 1.8V
T_AMB = 25°C
f_cIk = 3.58 MHz; V_DD = 3V
f_cIk = 16 MHz; V_DD = 5V
f_cIk = 16 MHz; V_DD = 5V
V_DD = 1.8V,
T_AMB = 25°C
-
-
25
µA
-
-
1.0
mA
-
-
10
mA
-
-
12
mA
-
10
µA
V_IL
V_IH
I_IL
I_TL
+/I_IL
Outputs
Input voltage LOW
Input voltage HIGH
Input current logic 0 (Port 1, 2, 3)
Input current logic 1 to 0 transition
(Port 1, 2, 3)
Input leakage current (Port 0, EA)
V_DD = 5V, V_IN = 0.4V
V_DD = 2.5V, V_IN = 0.4V
V_DD = 5V, V_IN = V_DD/2
V_DD = 2.5V, V_IN = V_DD/2
V_SS < V_I < V_DD
V_SS
-
0.3V_DD
V
0.7V_DD
-
V_DD
V
-
-
100
µA
-
-
50
µA
-
-
1.0
mA
-
-
500
µA
-
-
10
µA
I_OL
Output sink current LOW
V_DD = 5V, V_OL = 0.4V
V_DD = 2.5V, V_OL = 0.4V
1.6
-
0.7
-
-
mA
-
mA
-I_OH
Output source current HIGH
(push-pull options only)
V_DD = 5V; V_OH = V_DD -0.4V
V_DD = 2.5V; V_OH = V_DD -0.4V
1.6
-
0.7
-
-
mA
-
mA
R_RST RST pull-down resistor
10
–
200
kΩ
NOTES:
1. The operating supply current is measured with all output pins disconnected; XTAL 1 driven with t_r = t_f = 10ns; V_IL = V_SS; V_IH = V_DD;
XTAL 2 not connected; EA = RST = Port 0 = V_DD; all open drain outputs connected to V_SS.
2. The idle mode supply current is measured with all output pins disconnected; XTAL 1 driven with t_r = t_f = 10ns; V_IL = V_SS. XTAL 2 not
connected; EA = Port 0 = V_DD; RST = V_SS; all open drain outputs connected to V_SS.
3. The power-down current is measured with all output pins disconnected; XTAL 1 not connected; EA = Port 0 = V_DD; RST = V_SS; all open
drain outputs connected to V_SS.
4. Circuits with Power-on Reset option “OFF” are tested at V_DD minimum = 1.8V; with option “ON” (typically 1.3V) they are tested at V_DD
minimum = 2.3V. Please note, option “ON” is only available on P80CL51.
January 1995
27