MN101EFC3 Datasheet, PDF (16/46 Pages) Panasonic Semiconductor – 8-bit Single-chip Microcontroller

MN101EFC3/D3 Series
8-bit Single-chip Microcontroller
PubNo. 216C3-014E
Pins
P50
P51
P52
P53
P54
P55
P56
P57
P62
P63
P64
P65
P66
P67
P70
P71
P72
P73
P74
P75
P76
P77
P80
P81
P82
P83
P84
P85
P86
P87
P90
P91
P94
Pin No. I/O
52
I/O
53
54
55
56
57
58
59
51
I/O
50
49
48
47
46
45
I/O
44
43
42
41
40
39
38
37
I/O
36
35
34
33
32
31
30
8
I/O
9
60
Other Functions
SBO1A TXD1A
SEG15
SBI1A RXD1A
SEG16
SBT1A SEG17
SEG18 CTXA
SEG19 CRXA
SEG20 AN11
SEG21 AN10
SEG22 AN9
TM1IOB SEG14
TM3IOB SEG13
TM4IOB SEG12
SBO2A TXD2A
SEG11
SBI2A RXD2A
SEG10
SBT2A SEG9
KEY0 SBI4A
SEG8
KEY1 SBO4A
SDA4A SEG7
KEY2 SBT4A
SCL4A SEG6
KEY3 SEG5
KEY4 SEG4
KEY5 SBO1B
TXD1B SEG3
KEY6 SBI1B
RXD1B SEG2
KEY7 SBT1B
SEG1
SDO0 TM9OD0
SEG0
SDO1 TM9OD1
COM0
SDO2 TM9OD2
COM1
SDO3 TM9OD3
COM2
SDO4 TM9OD4
COM3
SDO5 TM9OD5
VLC3
SDO6 CRXB
VLC2
SDO7 CTXB
VLC1
XI
XO
AN8
SEG23
Functions
I/O port 5
I/O port 6
I/O port 7
I/O port 8
I/O port 9
Descriptions
8-bit CMOS tri-state I/O port.
Each bit can be set individually as either an input or out-
put by the P5DIR register.
A pull-up /pull-down resistor for each bit can be selected
individually by the P5PLUD register.
A pull-up/down resistor connection for each port can be
selected individually by the SELUD register. (A pull-up/
pull down can not be mixed.) At reset, the input mode is
selected and pull-up resistors are disabled (high imped-
ance)
6-bit CMOS tri-state I/O port.
Each bit can be set individually as either an input or out-
put by the P6DIR register.
A pull-up resistor for each bit can be selected individually
by the P6PLU register.
At reset, the input mode is selected and pull-up resistors
are disabled (high impedance)
8-bit CMOS tri-state I/O port.
Each bit can be set individually as either an input or
output by the P7DIR register. A pull-up /pull-down resistor
for each bit can be selected individually by the P7PLUD
register.
A pull-up/down resistor connection for each port can be
selected individually by the SELUD register. (A pull-up/
pull down can not be mixed.) At reset, the input mode is
selected and pull-up resistors are disabled (high
impedance)
8-bit CMOS tri-state I/O port.
Each bit can be set individually as either an input or out-
put by the P8DIR register.
A pull-up resistor for each bit can be selected individually
by the P8PLU register.
At reset, the input mode is selected and pull-up resistors
are disabled (high impedance)
3-bit CMOS tri-state I/O port.
Each bit can be set individually as either an input or out-
put by the P9DIR register.
A pull-up resistor for each bit can be selected individually
by the P9PLU register.
At reset, the input mode is selected and pull-up resistors
are disabled (high impedance)
Publication date: November 2015