DS90C2501 Datasheet, PDF (3/48 Pages) National Semiconductor (TI) – Transmitter with built-in scaler for LVDS Display Interface (LDI)

Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Supply Voltage (V_CC)
Supply Voltage (V_CC3V)
CMOS/TTL Input Voltage
CMOS/TTL Output
Voltage
LVDS Driver Output
Voltage
LVDS Output Short
Circuit Duration
Junction Temperature
Storage Temperature
Lead Temperature
(Soldering, 4 sec.)
−0.3V to +2.8V
−0.3V to +3.6V
−0.3V to V_CC3V
−0.3V to (V_CC + 0.3V)
−0.3V to (V_CC + 0.3V)
Continuous
+150˚C
−65˚C to +150˚C
+260˚C
Typical Package Power Dissipation Capacity @ 70˚C
and Max V_CC
128 CSP Package:
DS90C2501
1.8W
Maximum Operating Case Temperature: 97˚C
(measured at top center of package)
ESD Rating:
DS90C2501
(HBM, 1.5kΩ, 100pF)
(EIAJ, 0Ω, 200pF)
> 2 kV
> 250 V
Recommended Operating
Conditions
Min Nom Max Units
All Supply Voltage except 2.250 2.5 2.750 V
(V_CC3V)
V_CC3V Supply Voltage
Operating Free Air
3.0 3.3 3.6 V
Temperature (T_A)
0 +25 +70 ˚C
Supply Noise Voltage (V_CC)
100 mV_P-P
up to 33Mhz
DC Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max Units
LVCMOS/LVTTL DC SPECIFICATIONS (All input pins when operate in LVTTL level except DUAL pin. Note: On ID0, ID1
pins have typical 30K ohm internal pull-down, and ID2 and ID3 pins have typical 3K ohm internal pull-down.)
V_IH
High Level Input Voltage
V_REF = V_CC3V
V_IL
Low Level Input Voltage
V_REF = V_CC3V
V_CL
Input Clamp Voltage
I_CL = 18 mA
I_IN
Input Current
V_IN = 0.4V, or V_CC
V_IN = GND
LVCMOS/LVTTL DC SPECIFICATIONS for DUAL pin, pin35
2.0
V_CC3V
V
-0.3
0.8
V
-0.9
-1.5
V
+1.8
+15
µA
−15
0
µA
V_IH DUAL
High Level Input Voltage (for
dual pixel in to dual pixel
out).
PD = V_CC3V
2.0
V_CC
V
V_IM DUAL
High Level Input Voltage (for
single pixel in to dual pixel
out).
PD = V_CC3V
1_{⁄2VCC−0.1}
1_⁄2VCC 1_{⁄2VCC+0.1}
V
V_IL DUAL
High Level Input Voltage (for
single pixel in to single pixel
out).
PD = V_CC3V
0
0.4
V
V_CL
Input Clamp Voltage
I_CL = 18 mA
I_IN
Input Current
V_IN = 0.4V, V_CC
V_IN = Gnd
LVCMOS/LVTTL DC SPECIFICATIONS for MSEN, pin 98
-0.9
-1.5
V
1.8
15
µA
-15
0
µA
V_OL
Low level Open Drain Output I_OL = 2 mA
Voltage
0.1
0.3
V
LVCMOS/LVTTL DC SPECIFICATIONS (Pin 62 to pin 69 when operate in 3.3V LVTTL level)
V_OH
High Level Input Voltage
I_OL = 2 mA
V_OL
Low Level Input Voltage
I_OS
Output Short Circuit Current V_OUT = 0V
2.2
2.95
V
0.055
0.4
V
-50
−120
mA
3
www.national.com