PIC16F628-20P Datasheet, PDF (51/170 Pages) Microchip Technology – FLASH-Based 8-Bit CMOS Microcontroller

PIC16F62X
7.4 Timer1 Oscillator
A crystal oscillator circuit is built in between pins T1OSI
(input) and T1OSO (amplifier output). It is enabled by
setting control bit T1OSCEN (T1CON<3>). The oscilla-
tor is a low power oscillator rated up to 200 kHz. It will
continue to run during SLEEP. It is primarily intended
for a 32 kHz crystal. Table 7-1 shows the capacitor
selection for the Timer1 oscillator.
The Timer1 oscillator is identical to the LP oscillator.
The user must provide a software time delay to ensure
proper oscillator start-up.
TABLE 7-1: CAPACITOR SELECTION FOR
THE TIMER1 OSCILLATOR
Osc Type
Freq
C1
C2
LP
32 kHz
33 pF
33 pF
100 kHz
15 pF
15 pF
200 kHz
15 pF
15 pF
Note 1: These values are for design guidance only.
Consult AN826 (DS00826A) for further
information on Crystal/Capacitor Selection.
7.5 Resetting Timer1 Using a CCP
Trigger Output
If the CCP1 module is configured in Compare mode to
generate a “special event trigger” (CCP1M3:CCP1M0
= 1011), this signal will reset Timer1.
Note:
The special event triggers from the CCP1
module will not set interrupt flag bit
TMR1IF (PIR1<0>).
Timer1 must be configured for either Timer or Synchro-
nized Counter mode to take advantage of this feature.
If Timer1 is running in Asynchronous Counter mode,
this RESET operation may not work.
In the event that a write to Timer1 coincides with a
special event trigger from CCP1, the write will take
precedence.
In this mode of operation, the CCPRxH:CCPRxL
registers pair effectively becomes the period register
for Timer1.
7.6 Resetting of Timer1 Register Pair
(TMR1H, TMR1L)
TMR1H and TMR1L registers are not reset to 00h on a
POR or any other RESET except by the CCP1 special
event triggers.
T1CON register is reset to 00h on a Power-on Reset or
a Brown-out Reset, which shuts off the timer and
leaves a 1:1 prescale. In all other RESETS, the register
is unaffected.
7.7 Timer1 Prescaler
The prescaler counter is cleared on writes to the
TMR1H or TMR1L registers.
TABLE 7-2: REGISTERS ASSOCIATED WITH TIMER1 AS A TIMER/COUNTER
Address Name Bit 7 Bit 6 Bit 5
Bit 4
Bit 3
Bit 2 Bit 1
Bit 0
Value on
POR
Value on
all other
RESETS
0Bh/8Bh/ INTCON
10Bh/18Bh
GIE PEIE
T0IE
INTE
RBIE
T0IF
INTF
RBIF 0000 000x
0Ch
PIR1
EEIF CMIF RCIF
TXIF
—
CCP1IF TMR2IF TMR1IF 0000 -000
8Ch
PIE1
EEIE CMIE RCIE
TXIE
—
CCP1IE TMR2IE TMR1IE 0000 -000
0Eh
TMR1L Holding register for the Least Significant Byte of the 16-bit TMR1 register
xxxx xxxx
0Fh
TMR1H Holding register for the Most Significant Byte of the 16-bit TMR1 register
xxxx xxxx
10h
T1CON
—
— T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON --00 0000
Legend: x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used by the Timer1 module.
0000 000u
0000 -000
0000 -000
uuuu uuuu
uuuu uuuu
--uu uuuu
 2003 Microchip Technology Inc.
Preliminary
DS40300C-page 49