PIC24F08KA102-I Datasheet, PDF (152/278 Pages) Microchip Technology – 20/28-Pin General Purpose, 16-Bit Flash Microcontrollers with nanoWatt XLP Technology

PIC24F16KA102 FAMILY
REGISTER 18-2: UxSTA: UARTx STATUS AND CONTROL REGISTER
R/W-0
R/W-0
R/W-0
U-0
R/W-0, HC
R/W-0
UTXISEL1 UTXINV UTXISEL0
—
UTXBRK
UTXEN
bit 15
R-0, HSC
UTXBF
R-1, HSC
TRMT
bit 8
R/W-0
URXISEL1
bit 7
R/W-0
URXISEL0
R/W-0
ADDEN
R-1, HSC
RIDLE
R-0, HSC
PERR
R-0, HSC
FERR
R/C-0, HS
OERR
R-0, HSC
URXDA
bit 0
Legend:
C = Clearable bit
R = Readable bit
-n = Value at POR
HC = Hardware Clearable bit
HS = Hardware Settable bit HSC = Hardware Settable/Clearable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15,13
bit 14
bit 12
bit 11
bit 10
bit 9
bit 8
bit 7-6
UTXISEL<1:0>: Transmission Interrupt Mode Selection bits
11 = Reserved; do not use
10 = Interrupt when a character is transferred to the Transmit Shift Register (TSR), and as a result,
the transmit buffer becomes empty
01 = Interrupt when the last character is shifted out of the Transmit Shift Register; all transmit operations
are completed
00 = Interrupt when a character is transferred to the Transmit Shift Register (this implies there is at
least one character open in the transmit buffer)
UTXINV: IrDA^® Encoder Transmit Polarity Inversion bit
If IREN = 0:
1 = UxTX Idle ‘0’
0 = UxTX Idle ‘1’
If IREN = 1:
1 = UxTX Idle ‘1’
0 = UxTX Idle ‘0’
Unimplemented: Read as ‘0’
UTXBRK: Transmit Break bit
1 = Send Sync Break on next transmission – Start bit, followed by twelve ‘0’ bits, followed by Stop bit;
cleared by hardware upon completion
0 = Sync Break transmission is disabled or completed
UTXEN: Transmit Enable bit
1 = Transmit is enabled, UxTX pin is controlled by UARTx
0 = Transmit is disabled, any pending transmission is aborted and buffer is reset. UxTX pin is controlled
by the PORT register.
UTXBF: Transmit Buffer Full Status bit (read-only)
1 = Transmit buffer is full
0 = Transmit buffer is not full, at least one more character can be written
TRMT: Transmit Shift Register Empty bit (read-only)
1 = Transmit Shift Register is empty and transmit buffer is empty (the last transmission has completed)
0 = Transmit Shift Register is not empty, a transmission is in progress or queued
URXISEL<1:0>: Receive Interrupt Mode Selection bits
11 = Interrupt is set on RSR transfer, making the receive buffer full (i.e., has 4 data characters)
10 = Interrupt is set on RSR transfer, making the receive buffer 3/4 full (i.e., has 3 data characters)
0x = Interrupt is set when any character is received and transferred from the RSR to the receive buffer;
receive buffer has one or more characters
DS39927C-page 152
 2008-2011 Microchip Technology Inc.