LTC3869-2_15 Datasheet, PDF (27/42 Pages) Linear Technology – Dual, 2-Phase Synchronous Step-Down DC/DC Controllers

LTC3869/LTC3869-2
Applications Information
PC Board Layout Checklist
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of
the IC. These items are also illustrated graphically in the
layout diagram of Figure 11. Figure 12 illustrates the
current waveforms present in the various branches of
the 2-phase synchronous regulators operating in the
continuous mode. Check the following in your layout:
1. Are the top N-channel MOSFETs M1 and M3 located
within 1 cm of each other with a common drain con-
nection at C_IN? Do not attempt to split the input de-
coupling for the two channels as it can cause a large
resonant loop.
2. Are the signal and power grounds kept separate? The
combined IC signal ground pin and the ground return
of C_INTVCC must return to the combined C_OUT (–) ter-
minals. The V_FB and I_TH traces should be as short as
possible. The path formed by the top N-channel MOS-
FET, Schottky diode and the C_IN capacitor should have
short leads and PC trace lengths. The output capacitor
(–) terminals should be connected as close as possible
to the (–) terminals of the input capacitor by placing
the capacitors next to each other and away from the
Schottky loop described above.
3. Do the LTC3869 V_FB pins’ resistive dividers connect to
the (+) terminals of C_OUT? The resistive divider must be
connected between the (+) terminal of C_OUT and signal
ground. The feedback resistor connections should not
be along the high current input feeds from the input
capacitor(s).
4. Are the SENSE⁺ and SENSE^– leads routed together
with minimum PC trace spacing? The filter capacitor
between SENSE⁺ and SENSE^– should be as close as
possible to the IC. Ensure accurate current sensing with
Kelvin connections at the sense resistor or inductor,
whichever is used for current sensing.
5. Is the INTV_CC decoupling capacitor connected close
to the IC, between the INTV_CC and the power ground
pins? This capacitor carries the MOSFET drivers current
peaks. An additional 1µF ceramic capacitor placed im-
mediately next to the INTV_CC and PGND pins can help
improve noise performance substantially.
6. Keep the switching nodes (SW1, SW2), top gate nodes
(TG1, TG2), and boost nodes (BOOST1, BOOST2) away
from sensitive small-signal nodes, especially from the
opposite channel’s voltage and current sensing feed-
back pins. All of these nodes have very large and fast
moving signals and therefore should be kept on the
“output side” of the LTC3869 and occupy minimum
PC trace area. If DCR sensing is used, place the top
resistor (Figure 2b, R1) close to the switching node.
7. Use a modified “star ground” technique: a low imped-
ance, large copper area central grounding point on
the same side of the PC board as the input and output
capacitors with tie-ins for the bottom of the INTV_CC
decoupling capacitor, the bottom of the voltage feedback
resistive divider and the SGND pin of the IC.
PC Board Layout Debugging
Start with one controller at a time. It is helpful to use a
DC-50MHz current probe to monitor the current in the
inductor while testing the circuit. Monitor the output
switching node (SW pin) to synchronize the oscilloscope
to the internal oscillator and probe the actual output voltage
as well. Check for proper performance over the operating
voltage and current range expected in the application.
The frequency of operation should be maintained over
the input voltage range down to dropout and until the
output load drops below the low current operation
threshold—typically 10% of the maximum designed cur-
rent level in Burst Mode operation.
The duty cycle percentage should be maintained from
cycle to cycle in a well-designed, low noise PCB imple-
mentation. Variation in the duty cycle at a subharmonic
rate can suggest noise pickup at the current or voltage
sensing inputs or inadequate loop compensation. Over-
compensation of the loop can be used to tame a poor PC
layout if regulator bandwidth optimization is not required.
Only after each controller is checked for its individual
performance should both controllers be turned on at the
same time. A particularly difficult region of operation is
when one controller channel is nearing its current com-
parator trip point when the other channel is turning on
its top MOSFET. This occurs around 50% duty cycle on
either channel due to the phasing of the internal clocks
and may cause minor duty cycle jitter.
38692fa
For more information www.linear.com/LTC3869
27