LTC3786_15 Datasheet, PDF (15/34 Pages) Linear Technology – Low IQ Synchronous Boost Controller

LTC3786
Applications Information
less half the peak-to-peak ripple current, ∆I_L. To calculate
the sense resistor value, use the equation:
R_SENSE
=
V_{SENSE(MAX )}
I_MAX
+
∆I_L
2
When using the controller in low V_IN and very high voltage
output applications, the maximum inductor current and
correspondingly the maximum output current level will
be reduced due to the internal compensation required to
meet stability criterion for boost regulators operating at
greater than 50% duty factor. A curve is provided in the
Typical Performance Characteristics section to estimate
this reduction in peak inductor current level depending
upon the operating duty factor.
Inductor DCR Sensing
For applications requiring the highest possible efficiency
at high load currents, the LTC3786 is capable of sensing
the voltage drop across the inductor DCR, as shown in
Figure 2b. The DCR of the inductor can be less than 1mΩ
for high current inductors. In a high current application
requiring such an inductor, conduction loss through a
sense resistor could reduce the efficiency by a few percent
compared to DCR sensing.
If the external R1||R2 • C1 time constant is chosen to be
exactly equal to the L/DCR time constant, the voltage drop
across the external capacitor is equal to the drop across
the inductor DCR multiplied by R2/(R1 + R2). R2 scales the
voltage across the sense terminals for applications where
the DCR is greater than the target sense resistor value.
To properly dimension the external filter components, the
DCR of the inductor must be known. It can be measured
using a good RLC meter, but the DCR tolerance is not
always the same and varies with temperature. Consult
the manufacturer’s data sheets for detailed information.
Using the inductor ripple current value from the inductor
value calculation section, the target sense resistor value is:
R_{SENSE(EQUIV )}
=
V_{SENSE(MAX )}
I_MAX
+
∆I_L
2
To ensure that the application will deliver full load current
over the full operating temperature range, choose the
minimum value for the maximum current sense threshold
(V_SENSE(MAX)).
Next, determine the DCR of the inductor. Where provided,
use the manufacturer’s maximum value, usually given at
20°C. Increase this value to account for the temperature
coefficient of resistance, which is approximately 0.4%/°C. A
conservative value for the maximum inductor temperature
(T_L(MAX)) is 100°C.
To scale the maximum inductor DCR to the desired sense
resistor value, use the divider ratio:
R_D
=
R_{SENSE(EQUIV )}
DCR_MAX at T_L(MAX)
C1 is usually selected to be in the range of 0.1µF to 0.47µF.
This forces R1|| R2 to around 2k, reducing error that might
have been caused by the SENSE^– pin’s ±1µA current.
The equivalent resistance R1|| R2 is scaled to the room
temperature inductance and maximum DCR:
R1||
R2
=
(^DCR
at
L
20°C₎
•
C1
The sense resistor values are:
R1= ^{R1|| R2} ; R2 = ^{R1• RD}
R_D
1– R_D
The maximum power loss in R1 is related to duty cycle,
and will occur in continuous mode at V_IN = 1/2 V_OUT :
P_{LOSS _ R1}
=
(^V_OUT
• V_{IN )}
R1
•
V_IN
Ensure that R1 has a power rating higher than this value.
If high efficiency is necessary at light loads, consider this
power loss when deciding whether to use DCR sensing or
sense resistors. Light load power loss can be modestly
higher with a DCR network than with a sense resistor, due
to the extra switching losses incurred through R1. However,
DCR sensing eliminates a sense resistor, reduces conduc-
tion losses and provides higher efficiency at heavy loads.
Peak efficiency is about the same with either method.
3786fa
15