X98021 Datasheet, PDF (16/29 Pages) Intersil Corporation – 210MHz Triple Video Digitizer with Digital PLL

X98021
Offset can drift significantly over 50°C, reducing image
quality and requiring that the user do a manual calibration
once the monitor has warmed up.
In addition to drift, many AFEs exhibit interaction between
the offset and gain controls. When the gain is changed, the
magnitude of the offset is changed as well. This again
increases the complexity of the firmware as it tries to
optimize gain and offset settings for a given video input
signal. Instead of adjusting just the offset, then the gain, both
have to be adjusted interactively until the desired ADC
output is reached.
The X98021 simplifies offset and gain adjustment and
completely eliminates offset drift using its Automatic Black
Level Compensation (ABLC™) function. ABLC™ monitors
the black level and continuously adjusts the X98021's 10 bit
offset DACs to null out the offset. Any offset, whether due to
the video source or the X98021's analog amplifiers, is
eliminated with 10 bit (1/4 of an 8 bit ADC LSB) accuracy.
Any drift is compensated for well before it can have a visible
effect. Manual offset adjustment control is still available - an
8 bit register allows the firmware to adjust the offset ±64
codes in exactly 1 ADC LSB increments. And gain is now
completely independent of offset - adjusting the gain no
longer affects the offset, so there is no longer a need to
program the firmware to cope with interactive offset and gain
controls.
Finally, there should be no concerns over ABLC™ itself
introducing visible artifacts; it doesn't. ABLC™ operates at a
very low frequency, changing the offset in 1/4 LSB
increments, so it doesn't cause visible brightness
fluctuations. And once ABLC™ is locked, if the offset doesn't
drift, the DACs won't change. If desired, ABLC™ can be
disabled, allowing the firmware to work in the traditional way,
with 10 bit offset DACs under the firmware's control.
Gain and Offset Control
To simplify image optimization algorithms, the X98021
features fully-independent gain and offset adjustment.
Changing the gain does not affect the DC offset, and the
weight of an Offset DAC LSB does not vary depending on
the gain setting.
The full-scale gain is set in the three 8-bit registers (0x06-
0x08). The X98021 can accept input signals with amplitudes
ranging from 0.35V_P-P to 1.4V_P-P.
The offset controls shift the entire RGB input range,
changing the input image brightness. Three separate
registers provide independent control of the R, G, and B
channels. Their nominal setting is 0x80, which forces the
ADC to output code 0x00 (or 0x80 for U and V channels in
YUV mode) during the back porch period when ABLC™ is
enabled.
Functional Description
Inputs
The X98021 digitizes analog video inputs in both RGB and
Component (YPbPr) formats, with or without embedded sync
(SOG).
RGB Inputs
For RGB inputs, the black/blank levels are identical and
equal to 0V. The range for each color is typically 0V to 0.7V
from black to white. HSYNC and VSYNC are separate
signals.
Component YUV Inputs
In addition to RGB and RGB with SOG, the X98021 has an
option that is compatible with the component YPbPr and
YCbCr video inputs typically generated by DVD players.
While the X98021 digitizes signals in these color spaces, it
does not perform color space conversion; if it digitizes an
RGB signal, it outputs digital RGB, while if it digitizes a
YPbPr signal, it outputs digital YPbPr. For simplicity’s sake
we will call these non-RGB signals YUV.
The Luminance (Y) signal is applied to the Green Channel
and is processed in a manner identical to the Green input
with SOG described previously. The color difference signals
U and V are bipolar and swing both above and below the
black level. When the YUV mode is enabled, the black level
output for the color difference channels shifts to a mid scale
value of 0x80. Setting configuration register 0x05[2] = 1
enables the YUV signal processing mode of operation.
TABLE 1. YUV MAPPING (4:4:4)
INPUT
SIGNAL
X98021
INPUT
CHANNEL
X98021
OUTPUT
ASSIGNMENT
OUTPUT
SIGNAL
Y
Green
U
Blue
V
Red
Green
Blue
Red
Y₀Y₁Y₂Y₃
U₀U₁U₂U₃
V₀V₁V₂V₃
The X98021 can optionally decimate the incoming data to
provide a 4:2:2 output stream (configuration register
0x18[4] = 1) as shown in Table 2.
TABLE 2. YUV MAPPING (4:2:2)
INPUT
SIGNAL
X98021
INPUT
CHANNEL
X98021
OUTPUT
ASSIGNMENT
OUTPUT
SIGNAL
Y
Green
U
Blue
Green
Blue
Y₀Y₁Y₂Y₃
driven low
V
Red
Red
U₀V₁U₂V₃
16
FN8219.0
June 2, 2005