TLE8110EE_13 Datasheet, PDF (64/74 Pages) Infineon Technologies AG – Overvoltage, Overtemperature, ESD -Protection

DMSx/OPS1
1
DMSx/OPS2
1
DMSx/OPS3
1
DMSx/OPS4
1
DMSx/OPS5
1
DMSx/OPS6
1
DMSx/OPS7
1
DMSx/OPS8
1
DMSx
DMSx
DMSx
DMSx
DMSx
DMSx
DMSx
DMSx
TLE 8110 EE
Smart Multichannel Switch
Control of the device
0
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
0
Field
DCC_DRA
Bits
11:0
11:0
DCC_DRB
11:0
DCC_
DRACL
DCC_
11:0
DRBCL
DCC_
11:8
DMSCL
DCC_
11:8
DMS1
DCC_
11:8
DMS2
Type
W
W
W
W
W
W
W
Description
DRA - Diagnosis Register A (see Chapter 12.3.2.1)
Read out Diagnosis Register A. Return the contents in the next SPI
Frame. (see Chapter 12.3.2.2)
DRB - Diagnosis Register B (see Chapter 12.3.2.1)
Read out Diagnosis Register B. Return the contents in the next SPI
Frame. (see Chapter 12.3.2.2)
DRACL - Diagnosis Register A Clear
Clear the contents of the Diagnosis Register A. Return the content
present before the clear in the next SPI Frame. If the Diagnosis
Error Remains, the Information remains.(see Chapter 12.3.2.2)
DRBCL - Diagnosis Register B Clear
Clear the contents of the Diagnosis Register B. Return the content
present before the clear in the next SPI Frame. If the Diagnosis
Error Remains, the Information remains. (see
Chapter 12.3.2.2)
DMSCL/OPSx - Diagnosis Mode Set, Clear / Output Pins Set
On sending this command, the diagnosis registers DRA, DRB as well
as the “virtual” Diagnosis Output Registers DO[7:0] (see
Chapter 12.3.2.3) are cleared. Output Pin Settings are done
according the content of OPSx.
Returns the contents of cleared DR2 on SO in the 2nd byte of the
actual communication frame and the Output Pin Feedback in
the 1st Byte of the next frame. (see Chapter 12.3.2.3)
DMS1/OPSx - Diagnosis Mode Set, Register1 / Output Pins Set
On sending this command, the diagnosis registers DR1 is selected.
Output Pin Settings are done according the content of OPSx.
Returns the contents of DR1 on SO in the 2nd byte of the actual
communication frame and the Output Pin Feedback in the 1st
Byte of the next frame. (see Chapter 12.3.2.3)
DMS2/OPSx - Diagnosis Mode Set, Register2 / Output Pins Set
On sending this command, the diagnosis registers DR2 is selected.
Output Pin Settings are done according the content of OPSx.
Returns the contents of DR2 on SO in the 2nd byte of the actual
communication frame and the Output Pin Feedback in the 1st
Byte of the next frame. (see Chapter 12.3.2.3)
Data Sheet
64
Rev. 1.4, 2013-07-02