IC-MH_17 Datasheet, PDF (25/26 Pages) IC-Haus GmbH – 12-BIT ANGULAR HALL ENCODER

iC-MH
12-BIT ANGULAR HALL ENCODER
Rev C2, Page 25/26
REVISION HISTORY
Rel. Rel. Date^∗ Chapter
C1 2014-12-10 ELECTRICAL
CHARACTERISTICS
ELECTRICAL
CHARACTERISTICS
ELECTRICAL
CHARACTERISTICS
Modification
Item 003 max. value changed to 17 mA
Item 603 typical value 10% introduced, min./max. values changed to 15%
Item 710 max. values changed to 65 µA
Page
5
6
6
Rel. Rel. Date^∗ Chapter
C2 2016-12-09 ELECTRICAL
CHARACTERISTICS
Modification
Item 203 max value changed from 0.91 to 0.92
Item 205 min value changed from 1.1 to 1.0
Item 206 min value changed from 4.9 to 4.8
Item 404 min value changed from 3.7 to 3.65
Item 407 min value changed from 480 to 475
Item 502 min value changed from 14 to 13.5
Item 709 min value changed from 150 to 140
Item 803 min value changed from 150 to 140
Item 804 min value changed from 0.8 to 0.7
Item 904 min value changed from 150 to 140
Item 905 min value changed from -750 to -800
Page
5,6
BiSS Interface
BISS INTERFACE
DESCRIPTION
BLOCK DIAGRAM
PACKAGES
PACKAGING INFORMATION
ELECTRICAL
CHARACTERISTICS
REGISTER MAP
SENSOR PRINCIPLE
HALL SENSOR SIGNALS
HALL SENSOR SIGNALS
HALL SIGNAL PROCESSING
CALIBRATION PROCEDURE
OUTPUT DRIVERS
OTP PROGRAMMING
DESIGN REVIEW: Notes on Chip
Functions
BiSS Profile BP1 conformity with DLEN = 12 and BiSS.
21
BiSS Identifier updated.
Serial Interface updated to BiSS Interface and BiSS C protocol.
all
Headline changed from "Serial Interface" to "BISS INTERFACE"
20
BiSS User Agreement ”BUA” added
2
block diagram with new fill colour
1
package view with new style
1
Package drawing and suggested footprint added
3
Item 205, 206 old parameter names MINERR, MAXERR renamed to ERRAMIN, ERRA- 5
MAX
Footnote (*) added indicating register values pre-programmed by iC-Haus (affecting ad- 9
dresses 0x02, 0x04)
Figure 2 with new style
10
Headline changed from "POSITION OF THE HALL SENSORS and THE ANALOG SEN- 10
SOR SIGNAL" to "HALL SENSOR SIGNALS"
Figure 4 and 5 with new style
11
Note on default factory setting of bias register CIBM parameter
12
Note on default factory setting of bias register CIBM parameter
14
Figures 19 to 22 revised - settings of parameters CFGO, CFGRES, CFGDIR and CFG- 19
POLE added
Chapter revised, Figures 25 and 26 modified, Fig. 27 new introduced
23,24
Design Review introduced
24
iC-Haus expressly reserves the right to change its products and/or specifications. An Infoletter gives details as to any amendments and additions made to the
relevant current specifications on our internet website www.ichaus.com/infoletter and is automatically generated and shall be sent to registered users by email.
Copying – even as an excerpt – is only permitted with iC-Haus’ approval in writing and precise reference to source.
The data specified is intended solely for the purpose of product description and shall represent the usual quality of the product. In case the specifications contain
obvious mistakes e.g. in writing or calculation, iC-Haus reserves the right to correct the specification and no liability arises insofar that the specification was from
a third party view obviously not reliable. There shall be no claims based on defects as to quality in cases of insignificant deviations from the specifications or in
case of only minor impairment of usability.
No representations or warranties, either expressed or implied, of merchantability, fitness for a particular purpose or of any other nature are made hereunder
with respect to information/specification or the products to which information refers and no guarantee with respect to compliance to the intended use is given. In
particular, this also applies to the stated possible applications or areas of applications of the product.
iC-Haus products are not designed for and must not be used in connection with any applications where the failure of such products would reasonably be
expected to result in significant personal injury or death (Safety-Critical Applications) without iC-Haus’ specific written consent. Safety-Critical Applications
include, without limitation, life support devices and systems. iC-Haus products are not designed nor intended for use in military or aerospace applications or
environments or in automotive applications unless specifically designated for such use by iC-Haus.
iC-Haus conveys no patent, copyright, mask work right or other trade mark right to this product. iC-Haus assumes no liability for any patent and/or other trade
mark rights of a third party resulting from processing or handling of the product and/or any other use of the product.
Software and its documentation is provided by iC-Haus GmbH or contributors "AS IS" and is subject to the ZVEI General Conditions for the Supply of Products
and Services with iC-Haus amendments and the ZVEI Software clause with iC-Haus amendments (www.ichaus.com/EULA).
∗ _{Release Date format: YYYY-MM-DD}