US10D10A00 Datasheet, PDF (54/94 Pages) Honeywell Solid State Electronics Center – Basic Switches

Basic Switches
Miniature
CUTAWAY V7 MINIATURE BASIC SWITCH
V7 Series
FEATURES
ɀ Quick-connect and printed wiring
board termination
ɀ Proven V3 switching mechanism
ɀ Physically interchangeable with exist-
ing V3 switches
ɀ All existing V3 lever options available
ɀ UL recognized File # E12252; CSA cer-
tified File # LR41370
ɀ International listings carry VDE
approval
ɀ Power load switching capability up to
21 amps
ɀ Temperature tolerance –40° to 185°F
(–40° to 85°C)
ɀ High temperature construction
available—350°F
APPLICABLE EUROPEAN SYMBOLS
µ = microgap construction. (The
measurement between open
contacts is less than 3mm).**
ኈ _{= alternating current (used with}
value of voltage source:
250V ^ኈ).
T = maximum rated use
temperature; followed by the
temperature value in °C
(example T 85).
+++ = switch is rated for at least
50,000 cycles at its rated
current. (Sometimes referred
to as ‘‘frequent’’ operation.)
10(3) = first number represents
resistive rating. Second
number represents inductive
(motor) rating.
GENERAL INFORMATION
The V7 Series is available in two versions,
the Timesaver series and the International
series. The Timesaver series is UL recog-
nized and CSA certified. Timesaver series
switches use readily available high-vol-
ume components to provide especially
responsive delivery performance. The In-
ternational V7 provides VDE approval in
addition to UL recognition and CSA certi-
fication.
The V7 offers a choice of four quick-con-
nect and two printed wiring board termi-
nal types. Three quick-connect types are
offset to meet international 3mm spacing
requirements and one is designed for use
with molded connectors. Contact materi-
al choice includes gold alloy, silver alloy
or silver for handling various electrical
loads. There are two mounting hole sizes
available. Standard .114⍯ or 3mm to meet
European design requirements.
Terminal variations and switch dimen-
sions of the European designed version
conform to applicable DIN standards.
These V7s mate with both standard do-
mestic and international industry stan-
dard receptacles and connectors. The
plastic enclosure meets VDE KC250 arc
tracking requirement and is approvable
under the Refrigeration Industry Taste
and Odor test.
OPERATING FORCES
175 grams (V rating only)
150 grams (Not applicable to Electrical
Rating V)
75 grams (Not applicable to Electrical
Rating C or V)
50 grams (Not applicable to Electrical
Rating B, C, V)
25 grams (Not applicable to Electrical
Rating B, C, E, V)
15 grams (Not applicable to Electrical Rat-
ing A, B, C, E, S, V)
Mounting Torque:
2 inch pounds min.
5 inch pounds max.
ELECTRICAL RATINGS
A
B
5 amps, 125,
250 or 277
VAC; ⁄¹ 10 hp,
250 VAC
11 amps and ¹â„3
hp, 125, 250 or
277 VAC; ¹â„2
amp, 125 VDC;
1_{⁄4 amp, 250}
VDC; 4 amps,
125 VAC ‘‘L’’
W
X
15.1 amps,
6 amps; ¹â„8 HP
125, 250 or 277 125, 250 or 277
VAC
VAC
International Series Only
10 (3) +++
250V ^ኈ
T 85
µ
C*
15.1 amps and
1_{⁄2 hp, 125, 250}
or 277 VAC; ¹â„2
amp, 125 VDC;
1_{⁄4 amp, 250}
VDC; 5 amps,
120 VAC ‘‘L’’
D
1 amp, 125
VAC
* Available only when specifying 150 gram operating force.
NOTE: ‘‘L’’ denotes lamp load.
E
10 amps and ¹â„3
hp 125 or 250
VAC; ¹â„2 amp,
125 VDC; ¹â„4
amp, 250 VDC;
4 amps, 125
VAC ‘‘L’’
F
3 amps, 125,
250 or 277
VAC; ⁄¹ 10 hp,
250 VAC
S
.1 amp,
125 VAC
5 (2) +++
250V ^ኈ
T 85
µ
+++
V
21 amps 125,
250 or 277
VAC, 1 HP 125,
250, 277 VAC;
2 HP, 250, 277
VAC
16 (4)
250V ^ኈ
T 85
µ
50E3 SPNO only
** The microgap construction (M) means contact gap is less than 3mm. Therefore, these products are suitable for secondary circuit use but not
primary circuit use which requires a 3mm gap.
38 Honeywell Sensing and Control
For application help: call 1-800-537-6945.