|
MC9S12P32CFT Datasheet, PDF (260/566 Pages) Freescale Semiconductor, Inc – S12 Microcontrollers | |||
|
◁ |
Freescaleâs Scalable Controller Area Network (S12MSCANV3)
Table 8-4. CANCTL1 Register Field Descriptions (continued)
Field
2
WUPM
1
SLPAK
0
INITAK
Description
Wake-Up Mode â If WUPE in CANCTL0 is enabled, this bit deï¬nes whether the integrated low-pass ï¬lter is
applied to protect the MSCAN from spurious wake-up (see Section 8.4.5.5, âMSCAN Sleep Modeâ).
0 MSCAN wakes up on any dominant level on the CAN bus
1 MSCAN wakes up only in case of a dominant pulse on the CAN bus that has a length of Twup
Sleep Mode Acknowledge â This ï¬ag indicates whether the MSCAN module has entered sleep mode (see
Section 8.4.5.5, âMSCAN Sleep Modeâ). It is used as a handshake ï¬ag for the SLPRQ sleep mode request.
Sleep mode is active when SLPRQ = 1 and SLPAK = 1. Depending on the setting of WUPE, the MSCAN will
clear the ï¬ag if it detects activity on the CAN bus while in sleep mode.
0 Running â The MSCAN operates normally
1 Sleep mode active â The MSCAN has entered sleep mode
Initialization Mode Acknowledge â This ï¬ag indicates whether the MSCAN module is in initialization mode
(see Section 8.4.4.5, âMSCAN Initialization Modeâ). It is used as a handshake ï¬ag for the INITRQ initialization
mode request. Initialization mode is active when INITRQ = 1 and INITAK = 1. The registers CANCTL1,
CANBTR0, CANBTR1, CANIDAC, CANIDAR0âCANIDAR7, and CANIDMR0âCANIDMR7 can be written only by
the CPU when the MSCAN is in initialization mode.
0 Running â The MSCAN operates normally
1 Initialization mode active â The MSCAN has entered initialization mode
8.3.2.3 MSCAN Bus Timing Register 0 (CANBTR0)
The CANBTR0 register conï¬gures various CAN bus timing parameters of the MSCAN module.
Module Base + 0x0002
Access: User read/write(1)
7
R
SJW1
W
6
SJW0
5
BRP5
4
BRP4
3
BRP3
2
BRP2
Reset:
0
0
0
0
0
0
Figure 8-6. MSCAN Bus Timing Register 0 (CANBTR0)
1. Read: Anytime
Write: Anytime in initialization mode (INITRQ = 1 and INITAK = 1)
1
BRP1
0
0
BRP0
0
Table 8-5. CANBTR0 Register Field Descriptions
Field
Description
7-6
SJW[1:0]
5-0
BRP[5:0]
Synchronization Jump Width â The synchronization jump width deï¬nes the maximum number of time quanta
(Tq) clock cycles a bit can be shortened or lengthened to achieve resynchronization to data transitions on the
CAN bus (see Table 8-6).
Baud Rate Prescaler â These bits determine the time quanta (Tq) clock which is used to build up the bit timing
(see Table 8-7).
Table 8-6. Synchronization Jump Width
SJW1
0
SJW0
0
Synchronization Jump Width
1 Tq clock cycle
S12P-Family Reference Manual, Rev. 1.13
260
Freescale Semiconductor
|
▷ |