MC33912_10 Datasheet, PDF (12/94 Pages) Freescale Semiconductor, Inc – LIN System Basis Chip with DC Motor Pre-driver and Current Sense

ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
MC33912G5AC / MC34912G5AC
Table 4. Static Electrical Characteristics (continued)
Characteristics noted under conditions 5.5 V ≤ V_SUP ≤ 18 V, -40°C ≤ T_A ≤ 125°C for the 33912 and -40°C ≤ T_A ≤ 85°C for the
34912, unless otherwise noted. Typical values noted reflect the approximate parameter mean at T_A = 25°C under nominal
conditions, unless otherwise noted.
Characteristic
HIGH SIDE OUTPUTS HS1 AND HS2 PINS (HS1, HS2)
Symbol
Min
Typ
Max
Unit
Output Drain-to-Source On Resistance
T_J = 25°C, I_LOAD = 50 mA; V_SUP > 9.0 V
T_J = 150°C, I_LOAD = 50 mA; V_SUP > 9.0 V⁽²⁵⁾
T_J = 150°C, I_LOAD = 30 mA; 5.5 V < V_SUP < 9.0 V⁽²⁵⁾
Output Current Limitation⁽²⁶⁾
0 V < V_OUT < V_SUP - 2.0 V
Open Load Current Detection⁽²⁷⁾
Leakage Current
-0.2 V < V_HSX < V_S2 + 0.2 V
Short-circuit Detection Threshold⁽²⁸⁾
5.5 V < V_SUP < 27 V
Over-temperature Shutdown^{(29), (33)}
Over-temperature Shutdown Hysteresis⁽³³⁾
LOW SIDE OUTPUTS LS1 AND LS2 PINS (LS1, LS2)
R_DS(ON)
–
–
–
Ω
–
7.0
–
10
–
14
I_LIMHSX
mA
60
90
250
I_OLHSX
–
5.0
7.5
mA
I_LEAK
µA
–
–
10
V_THSC
V
V_SUP -2.0
–
–
T_HSSD
140
160
180
°C
T_{HSSD_HYS}
–
10
–
°C
Output Drain-to-Source On Resistance
T_J = 25°C, I_LOAD = 150 mA, V_SUP > 9.0 V
T_J = 125°C, I_LOAD = 150 mA, V_SUP > 9.0 V
T_J = 125°C, I_LOAD = 120 mA, 5.5 V < V_SUP < 9.0 V
Output Current Limitation⁽³⁰⁾
2.0 V < V_OUT < V_SUP
Open Load Current Detection⁽³¹⁾
Leakage Current
-0.2 V < V_OUT < VS1
R_DS(ON)
–
–
–
Ω
–
2.5
–
4.5
–
10
I_LIMLSX
I_OLLSX
I_LEAK
mA
160
275
350
–
7.5
12
mA
µA
–
–
10
Active Output Energy Clamp
I_OUT = 150 mA
V_CLAMP
V
V_SUP +2.0
–
V_SUP +5.0
Short-circuit Detection Threshold⁽²⁸⁾
5.5 V < V_SUP < 27 V
V_THSC
V
2.0
–
–
Over-temperature Shutdown^{(32), (33)}
Over-temperature Shutdown Hysteresis⁽³³⁾
T_LSSD
140
160
180
°C
T_{LSSD_HYS}
–
10
–
°C
Notes
25. This parameter is production tested up to T_A = 125°C, and guaranteed by process monitoring up to T_J = 150°C.
26. When over-current occurs, the corresponding high side stays ON with limited current capability and the HSxCL flag is set in the HSSR.
27. When open load occurs, the flag (HSxOP) is set in the HSSR.
28. HS and LS automatically shutdown if HSOT or LSOT occurs or if the HVSE flag is enabled and an over-voltage occurs.
29. When over-temperature shutdown occurs, both high sides are turned off. All flags in HSSR are set.
30. When over-current occurs, the corresponding low side stays ON with limited current capability and the LSxCL flag is set in the LSSR.
31. When open load occurs, the flag (LSxOP) is set in the LSSR.
32. When over-temperature shutdown occurs, both low sides are turned off. All flags in LSSR are set.
33. Guaranteed by characterization but not production tested
33912
12
Analog Integrated Circuit Device Data
Freescale Semiconductor