CH1005C Datasheet, PDF (14/49 Pages) List of Unclassifed Manufacturers – Digital PC to TV Encoder with Macrovision

CHRONTEL
CH7005C
Display Modes (continued)
additional filtering for enhancing the readability of text. These modes are fully programmable via I²C under the
flicker filter register.
Internal Voltage Reference
An onchip bandgap circuit is used in the DAC to generate a reference voltage which, in conjunction with a reference
resistor at pin RSET, and register controlled divider, sets the output ranges of the DACs. The CH7005 bandgap
reference voltage is 1.235 volts nominal for NTSC or PAL-M, or 1.317 volts nominal (for PAL or NTSC-J), which
is determined by IDF register bit 6 (DACG bit). The recommended value for the reference resistor RSET is 360
ohms (though this may be adjusted in order to achieve a different output level). The gain setting for DAC output is
1/48^th. Therefore, for each DAC, the current output per LSB step is determined by the following equation:
I_LSB = V(RSET)/RSET reference resistor * 1/GAIN
For DACG=0, this is: I_LSB = 1.235/360 * 1/48 = 71.4 µA (nominal)
For DACG=1, this is: I_LSB = 1.317/360 * 1/48 = 76.2 µA (nominal)
Power Management
The CH7005 supports five operating states including Normal [On], Power Down, Full Power Down, S-Video Off,
and Composite Off to provide optimal power consumption for the application involved. Using the programmable
power down modes accessed over the I²C port, the CH7005 may be placed in either Normal state, or any of the four
power managed states, as listed below (see “Power Management Register” under the Register Descriptions section
for programming information). To support power management, a TV sensing function (see “Connection Detect
Register” under the Register Descriptions section) is provided, which identifies whether a TV is connected to either
S-Video or composite. This sensing function can then be used to enter into the appropriate operating state (e.g., if
TV is sensed only on composite, the S-Video Off mode could be set by software).
Table 11. Power Management
Operating State
Normal (On):
Power Down:
S-Video Off:
Composite Off:
Full Power Down:
Functional Description
In the normal operating state, all functions and pins are active
In the power-down state, most pins and circuitry are disabled.The DS/BCO pin
will continue to provide either the VCO divided by K3, or 14.318 MHz out when
selected as an output, and the P-OUT pin will continue to output a clock
reference when in master clock mode.
Power is shut off to the unused DACs associated with S-Video outputs.
In Composite-off state, power is shut off to the unused DAC associated with
CVBS output.
In this power-down state, all but the I²C circuits are disabled. This places the
CH7005 in its lowest power consumption mode.
Luminance and Chrominance Filter Options
The CH7005 contains a set of luminance filters to provide a controllable bandwidth output on both CVBS and S-
Video outputs. All values are completely programmable via the Video Bandwidth Register. For all graphs shown,
the horizontal axis is frequency in MHz, and the vertical axis is attenuation in dBs. The composite luminance and
chrominance video bandwidth output is shown in Table 12.
Macrovision^TM Anti-copy Protection
The CH7005 implements the Macrovision 7.X anti-copy protection process. This process changes the encoded
output of the NTSC/PAL signals to inhibit recording on VCR devices while not affecting viewing on a TV. The
parameters that control this process are fully programmable and can be described by Chrontel only after a suitable
Non-Disclosure Agreement has been executed between Macrovision^TM, Inc. and the customer.
14
201-0000-025 Rev 2.1, 8/2/99