EN25QH128A Datasheet, PDF (1/75 Pages) Eon Silicon Solution Inc. – 128 Megabit Serial Flash Memory with 4Kbyte Uniform Sector

EN25QH128A
EN25QH128A
128 Megabit Serial Flash Memory with 4Kbyte Uniform Sector
FEATURES
• Single power supply operation
- Full voltage range: 2.7-3.6 volt
• Serial Interface Architecture
- SPI Compatible: Mode 0 and Mode 3
• 128 M-bit Serial Flash
- 128 M-bit/16,384 K-byte/65,536 pages
- 256 bytes per programmable page
• Standard, Dual or Quad SPI
- Standard SPI: CLK, CS#, DI, DO, WP#, HOLD#
- Dual SPI: CLK, CS#, DQ₀, DQ₁, WP#, HOLD#
- Quad SPI: CLK, CS#, DQ₀, DQ₁, DQ₂, DQ₃
• High performance
- 104MHz clock rate for Standard SPI
- 104MHz clock rate for two data bits
- 80MHz clock rate for four data bits
• Burst Modes
- Continuous linear burst
- 8/16/32/64/128/256 linear burst with wrap-
around
• Low power consumption
- 12 mA typical active current
- 1 μA typical power down current
• Uniform Sector Architecture:
- 4096 sectors of 4-Kbyte
- 512 blocks of 32-Kbyte
- 256 blocks of 64-Kbyte
- Any sector or block can be erased individually
• Software and Hardware Write Protection:
- Write Protect all or portion of memory via
software
- Enable/Disable protection with WP# pin
• High performance program/erase speed
- Page program time: 0.8ms typical
- Sector erase time: 50ms typical
- 32KB Block erase time 100ms typical
- 64KB Block erase time 200ms typical
- Chip erase time: 45 seconds typical
• Write Suspend and Write Resume
• Lockable 512 byte OTP security sector
• Support Serial Flash Discoverable
Parameters (SFDP) signature
• Read Unique ID Number
• Minimum 100K endurance cycle
• Package Options
- 8 pins SOP 200mil body width
- 8 pins VSOP 200mil body width
- 8 contact VDFN (5x6mm)
- 8 contact VDFN (6x8mm)
- 8 pins PDIP
- 16 pins SOP 300mil body width
- 24 balls TFBGA (6x8mm)
- All Pb-free packages are compliant RoHS,
Halogen-Free and REACH.
• Industrial temperature Range
GENERAL DESCRIPTION
The EN25QH128A is a 128 Megabit (16,384 K-byte) Serial Flash memory, with enhanced write
protection mechanisms. The EN25QH128A supports the standard Serial Peripheral Interface (SPI), and
a high performance Dual/Quad output as well as Dual/Quad I/O using SPI pins: Serial Clock, Chip
Select, Serial DQ₀(DI), DQ₁(DO), DQ₂(WP#) and DQ₃(HOLD#). SPI clock frequencies of up to 104MHz
are supported allowing equivalent clock rates of 208MHz (104MHz x 2) for Dual Output and 320MHz
(80MHz x 4) for Quad Output when using the Dual/Quad I/O Fast Read instructions. The memory can
be programmed 1 to 256 bytes at a time, using the Page Program instruction.
The EN25QH128A is designed to allow either single Sector/Block at a time or full chip erase operation.
The EN25QH128A can be configured to protect part of the memory as the software protected mode.
The device can sustain a minimum of 100K program/erase cycles on each sector or block.
This Data Sheet may be revised by subsequent versions
1
or modifications due to changes in technical specifications.
©2014 Eon Silicon Solution, Inc.,
Rev. C, Issue Date: 2014/01/22
www.eonssi.com