LUPA-1300_09 Datasheet, PDF (22/32 Pages) Cypress Semiconductor – 1.3MPxl High Speed CMOS Image Sensor

LUPA-1300
Table 11. Pin description of the assembled LUPA-1300 sensor in the PGA 144 package (continued)
Pin
N3
N4
N5
P3
P5
P4
Q1
N6
P6
Q2
Q3
Q4
N7
P7
Q5
Q6
Q7
N8
P8
Q8
Q9
P9
N9
Q10
Q11
Q12
P10
N10
Q13
P11
P12
N11
N12
P13
N13
M13
Q14
P14
fp
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
Name
Gnd
Voo
Vstable
Load_out
Dc_black
Vdd
Gnd
Vdda
Gnd
Vpix
Eos_x
Nsf_load
Psf_load
Col_load
Pre_load
n.c.
Array_diode
Full_diode
Temp_diode_p
Temp_diode_n
n.c.
n.c.
n.c.
n.c.
n.c.
n.c.
n.c.
n.c.
n.c.
Vpix
Gnd
Vddr
n.c.
Vmem_l
Vmem_h
Vres_ds
Vres
Gnd_res
Function
Ground
Supply 5V
Supply 5V
Biasing
Testpin 6
Supply 5V
Ground
Supply 5V
Ground
Supply 4.5V
Digital I/O
Biasing
Biasing
Biasing
Biasing
Testpin 3
Testpin 4
Testpin 1
Testpin 2
Supply 4.5V
Ground
Supply 5V
Supply
Supply
Supply
Supply
Ground_ab
Description
Ground of the sensor
Supply voltage output stages: 5V
Supply voltage to stabilize output stages: 5.5V
Analog bias for output amplifiers 27 KΩ to Voo and
capacitor of 100 nF to ground
dc-black signal required to characterize the output
stages
Supply voltage digital modules: 5V
Ground of the sensor
Supply voltage analog modules: 5V
Ground of the sensor
Supply voltage pixel array: 4.5V
End of scan signal of the x-register: active high pulse
indicates the end of the shift register is reached
Analog bias for column stages: 100 KΩ to Vdda and
capacitor of 100nF to ground
Analog bias for column stages: 240 KΩ to gnd and
capacitor of 100 nF to Vdda
Analog bias for column stages: 2 MΩ to Vdda and
capacitor of 100 nF to ground
Analog bias for column stages: 10 KΩ to Vdda and
capacitor of 100 nF to ground
Array of pixels as designed in pixel array
Full diode with same array as array diode: 140 * 70 µm²
Temperature diode p side
Temperature diode n side
Supply voltage pixel array: 4.5V
Ground of the sensor
Supply voltage of the logic for the drivers: 5V
Voltage supply for Vmemory drivers: 3V- 5V (typ: 4.5V)
Voltage supply for Vmemory drivers: 4V- 6V (typ. 6V)
Voltage supply for reset double sloped drivers: 4V - 5V
Voltage supply for reset drivers: 5V - 6V (typ 6V)
Ground anti-blooming: 0 - 1V
Document Number: 38-05711 Rev. *C
Page 22 of 32
[+] Feedback