X5001 Datasheet, PDF (9/19 Pages) Xicor Inc. – CPU Supervisor

X5001
ABSOLUTE MAXIMUM RATINGS*
*COMMENT
Temperature under Bias ........................–65°C to +135°C
Storage Temperature .............................–65°C to +150°C
Voltage on any Pin with Respect to V_SS....... –1.0V to +7V
D.C. Output Current ....................................................5mA
Lead Temperature (Soldering, 10 seconds)............ 300°C
RECOMMENDED OPERATING CONDITIONS
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only and the functional operation of
the device at these or any other conditions above those
listed in the operational sections of this specification is not
implied. Exposure to absolute maximum rating conditions
for extended periods may affect device reliability.
Temp
Commercial
Min.
0°C
Max.
+70°C
7036 FRM T07
Voltage Option
–1.8
–2.7 or -2.7A
Supply Voltage Limits
1.8V to 3.6V
2.7V to 5.5V
–4.5 or -4.5A
4.5V to 5.5V
PT= Package, Temperature
D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.)
Symbol
Parameter
I_CC1 V_CC Write Current (Active)
I_CC2 V_CC Read Current (Active)
I_SB1
I_SB2
I_SB3
I_LI
I_LO
V_IL⁽¹⁾
V_IH⁽¹⁾
V_OL1
V_OL2
V_OL3
V_OH1
V_OH2
V_OH3
V_OLRS
V_CC Standby Current WDT=OFF
V_CC Standby Current WDT=ON
V_CC Standby Current WDT=ON
Input Leakage Current
Output Leakage Current
Input LOW Voltage
Input HIGH Voltage
Output LOW Voltage
Output LOW Voltage
Output LOW Voltage
Output HIGH Voltage
Output HIGH Voltage
Output HIGH Voltage
Reset Output LOW Voltage
Limits
Min. Typ. Max. ^Units
Test Conditions
5
mA
SCK = V_CC x 0.1/V_CC x 0.9 @ 5MHz,
SO = Open
0.4
mA
SCK = V_CC x 0.1/V_CC x 0.9 @ 5MHz,
SO = Open
1
µA CS = V_CC, V_IN = V_SS or V_CC, V_CC = 5.5V
50
µA CS = V_CC, V_IN = V_SS or V_CC, V_CC = 5.5V
20
µA CS = V_CC, V_IN = V_SS or V_CC, V_CC =3.6V
0.1 10
µA V_IN = V_SS to V_CC
0.1 10
µA V_OUT = V_SS to V_CC
–0.5
V_CCx0.3 V
V_CCx0.7
V_CC+0.5 V
0.4
V V_CC > 3.3V, I_OL = 2.1mA
0.4
V 2V < V_CC < 3.3V, I_OL = 1mA
0.4
V _VCC ≤ 2V, I_OL = 0.5mA
V_CC–0.8
V V_CC > 3.3V, I_OH = –1.0mA
V_CC–0.4
V _{2V < VCC} ≤ 3.3V, I_OH = –0.4mA
V_CC–0.2
V _VCC ≤ 2V, I_OH = –0.25mA
0.4
V I_OL = 1mA
POWER-UP TIMING
Symbol
t_PUR⁽²⁾
t_PUW⁽²⁾
Parameter
Power-up to Read Operation
Power-up to Write Operation
Min.
Max.
1
5
Units
ms
ms
CAPACITANCE T_A = +25°C, f = 1MHz, V_CC = 5V.
Symbol
Test
C_OUT^{(2) Output Capacitance (SO, RESET)}
C_IN⁽²⁾
Input Capacitance (SCK, SI, CS)
Notes: (1) V_IL min. and V_IH max. are for reference only and are not tested.
(2) This parameter is periodically sampled and not 100% tested.
Max.
8
6
Units
pF
pF
Conditions
V_OUT = 0V
V_IN = 0V
9