 English |
|
|
|
|
|
|
|
| AM1806_11 Datasheet, PDF (99/244 Pages) Texas Instruments – AM1806 ARM Microprocessor | |||
| |||
| ◁ |
AM1806
www.ti.com
SPRS658C â FEBRUARY 2010 â REVISED APRIL 2011
NO.
1
td(TURNAROUND)
3
tc(EMRCYCLE)
4
tsu(EMCEL-EMOEL)
5
th(EMOEH-EMCEH)
6
tsu(EMBAV-EMOEL)
7
th(EMOEH-EMBAIV)
8
tsu(EMBAV-EMOEL)
9
th(EMOEH-EMAIV)
10 tw(EMOEL)
11
td(EMWAITH-EMOEH)
15
tc(EMWCYCLE)
16
tsu(EMCEL-EMWEL)
17
th(EMWEH-EMCEH)
18
tsu(EMDQMV-EMWEL)
19
th(EMWEH-EMDQMIV)
20
tsu(EMBAV-EMWEL)
21
th(EMWEH-EMBAIV)
22
tsu(EMAV-EMWEL)
23
th(EMWEH-EMAIV)
Table 5-22. Switching Characteristics for EMIFA Asynchronous Memory Interface (1) (2) (3)
PARAMETER
MIN
READS and WRITES
Turn around time
(TA)*E - 3
READS
EMIF read cycle time (EW = 0)
(RS+RST+RH)*E - 3
EMIF read cycle time (EW = 1)
(RS+RST+RH+(EWC*16))*E
-3
Output setup time, EMA_CE[5:2] low to EMA_OE low (SS = 0)
(RS)*E-3
Output setup time, EMA_CE[5:2] low to EMA_OE low (SS = 1)
-3
Output hold time, EMA_OE high to EMA_CE[5:2] high (SS = 0)
(RH)*E - 3
Output hold time, EMA_OE high to EMA_CE[5:2] high (SS = 1)
-3
Output setup time, EMA_BA[1:0] valid to EMA_OE low
(RS)*E-3
Output hold time, EMA_OE high to EMA_BA[1:0] invalid
(RH)*E-3
Output setup time, EMA_A[13:0] valid to EMA_OE low
(RS)*E-3
Output hold time, EMA_OE high to EMA_A[13:0] invalid
(RH)*E-3
EMA_OE active low width (EW = 0)
(RST)*E-3
EMA_OE active low width (EW = 1)
(RST+(EWC*16))*E-3
Delay time from EMA_WAIT deasserted to EMA_OE high
3E-3
WRITES
EMIF write cycle time (EW = 0)
(WS+WST+WH)*E-3
EMIF write cycle time (EW = 1)
(WS+WST+WH+(EWC*16))*
E-3
Output setup time, EMA_CE[5:2] low to EMA_WE low (SS = 0)
(WS)*E - 3
Output setup time, EMA_CE[5:2] low to EMA_WE low (SS = 1)
-3
Output hold time, EMA_WE high to EMA_CE[5:2] high (SS = 0)
(WH)*E-3
Output hold time, EMA_WE high to EMA_CE[5:2] high (SS = 1)
-3
Output setup time, EMA_BA[1:0] valid to EMA_WE low
(WS)*E-3
Output hold time, EMA_WE high to EMA_BA[1:0] invalid
(WH)*E-3
Output setup time, EMA_BA[1:0] valid to EMA_WE low
(WS)*E-3
Output hold time, EMA_WE high to EMA_BA[1:0] invalid
(WH)*E-3
Output setup time, EMA_A[13:0] valid to EMA_WE low
(WS)*E-3
Output hold time, EMA_WE high to EMA_A[13:0] invalid
(WH)*E-3
1.3V,1.2V, 1.1V, 1.0V
Nom
MAX
(TA)*E
(TA)*E + 3
(RS+RST+RH)*E
(RS+RST+RH)*E + 3
(RS+RST+RH+(EWC*16))*E
(RS+RST+RH+(EWC*16))*E
+3
(RS)*E
(RS)*E+3
0
+3
(RH)*E
(RH)*E + 3
0
+3
(RS)*E
(RS)*E+3
(RH)*E
(RH)*E+3
(RS)*E
(RS)*E+3
(RH)*E
(RH)*E+3
(RST)*E
(RST)*E+3
(RST+(EWC*16))*E
(RST+(EWC*16))*E+3
4E
4E+3
(WS+WST+WH)*E
(WS+WST+WH)*E+3
(WS+WST+WH+(EWC*16))*E
(WS+WST+WH+(EWC*16))*
E+3
(WS)*E
(WS)*E + 3
0
+3
(WH)*E
(WH)*E+3
0
+3
(WS)*E
(WS)*E+3
(WH)*E
(WH)*E+3
(WS)*E
(WS)*E+3
(WH)*E
(WH)*E+3
(WS)*E
(WS)*E+3
(WH)*E
(WH)*E+3
UNIT
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
(1) TA = Turn around, RS = Read setup, RST = Read strobe, RH = Read hold, WS = Write setup, WST = Write strobe, WH = Write hold, MEWC = Maximum external wait cycles. These
parameters are programmed via the Asynchronous Bank and Asynchronous Wait Cycle Configuration Registers. These support the following range of values: TA[4-1], RS[16-1],
RST[64-1], RH[8-1], WS[16-1], WST[64-1], WH[8-1], and MEW[1-256].
(2) E = EMA_CLK period or in ns. EMA_CLK is selected either as SYSCLK3 or the PLL0 output clock divided by 4.5. As an example, when SYSCLK3 is selected and set to 100MHz, E=10ns.
(3) EWC = external wait cycles determined by EMA_WAIT input signal. EWC supports the following range of values EWC[256-1]. Note that the maximum wait time before timeout is specified
by bit field MEWC in the Asynchronous Wait Cycle Configuration Register.
Copyright © 2010â2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): AM1806
Peripheral Information and Electrical Specifications
99
|
▷ |
German
Russian
Spanish
Italian
Polish
Chinese
Japanese
Korean
French
Portuguese