DS99R103_14 Datasheet, PDF (4/30 Pages) Texas Instruments – 3-40MHz DC-Balanced 24-Bit LVDS Serializer and Deserializer

DS99R103, DS99R104
SNLS241D – MARCH 2007 – REVISED APRIL 2013
www.ti.com
Electrical Characteristics^(1)(2)(3)
Over recommended operating supply and temperature ranges unless otherwise specified.
Parameter
Test Conditions
Pin/Freq.
LVCMOS/LVTTL DC SPECIFICATIONS
V_IH
High Level Voltage
V_IL
Low Level Input Voltage
V_CL
Input Clamp Voltage
I_CL = −18 mA⁽⁴⁾
Tx: DIN[23:0], TCLK,
TPWDNB, DEN, TRFB,
DCAOFF, DCBOFF,
VODSEL
Rx: RPWDNB, RRFB,
REN
I_IN
Input Current
V_IN = 0V or 3.6V
Tx: DIN[23:0], TCLK,
TPWDNB, DEN, TRFB,
DCAOFF, DCBOFF,
VODSEL
Rx: RPWDNB, RRFB,
REN
V_OH
High Level Output Voltage
V_OL
Low Level Output Voltage
I_OS
Output Short Circuit Current
I_OZ
TRI-STATE Output Current
LVDS DC SPECIFICATIONS
I_OH = −4 mA
I_OL = +4 mA
V_OUT = 0V⁽⁴⁾
RPWDNB, REN = 0V
V_OUT = 0V or 2.4V
Rx: ROUT[23:0], RCLK,
LOCK
Rx: ROUT[23:0], RCLK,
LOCK
V_TH
Differential Threshold High
V_CM = +1.2V
Voltage
Rx: R_IN+, R_IN−
V_TL
Differential Threshold Low
Voltage
I_IN
Input Current
V_IN = +2.4V,
V_DD = 3.6V
V_IN = 0V, V_DD = 3.6V
R_T
Differential Internal
Termination Resistance
V_OD
Output Differential Voltage
R_L = 100Ω, w/o Pre-emphasis
(D_OUT+)–(D_OUT−)
VODSEL = L (Figure 10)
R_L = 100Ω, w/o Pre-emphasis
VODSEL = H (Figure 10)
Tx: D_OUT+, D_OUT−
ΔV_OD
Output Differential Voltage
Unbalance
R_L = 100Ω, w/o Pre-emphasis
V_OS
ΔV_OS
I_OS
Offset Voltage
Offset Voltage Unbalance
Output Short Circuit Current
R_L = 100Ω, w/o Pre-emphasis
R_L = 100Ω, w/o Pre-emphasis
DOUT = 0V, DIN = H,
TPWDNB, DEN = 2.4V,
VODSEL = L
DOUT = 0V, DIN = H,
TPWDNB, DEN = 2.4V,
VODSEL = H
I_OZ
TRI-STATE Output Current TPWDNB, DEN = 0V,
DOUT = 0V or 2.4V
Min Typ Max Units
2.0 1.5 V_DD
V
GND 1.5 0.8
V
−0.8 −1.5 V
−10 ±1 +10 µA
−20 ±5 +20 µA
2.3 3.0 V_DD
V
GND 0.33 0.5
V
−40 −70 −110 mA
−30 ±0.4 +30 µA
+50 mV
−50
mV
±300 µA
±300 µA
90 100 130 Ω
250 400 600 mV
450 750 1200 mV
4
50
mV
1.00 1.25 1.50 V
1
50
mV
−2 −5 −8 mA
−7 −10 −13 mA
−15 ±1 +15 µA
(1) The Electrical Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except as
otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and
are not ensured.
(2) Typical values represent most likely parametric norms at VDD = 3.3V, TA = +25 degC, and at the Recommended Operation Conditions
at the time of product characterization and are not ensured.
(3) Current into device pins is defined as positive. Current out of a device pin is defined as negative. Voltages are referenced to ground
except VOD, ΔVOD, VTH and VTL which are differential voltages.
(4) Specification is ensured by characterization and is not tested in production.
4
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS99R103 DS99R104