RX111_16 Datasheet, PDF (64/127 Pages) Renesas Technology Corp – 32 MHz 32-bit RX MCUs, 50 DMIPS, up to 512 Kbytes of flash memory

RX111 Group
5. Electrical Characteristics
Table 5.12 DC Characteristics (10)
Conditions: 1.8 V ≤ VCC = VCC_USB ≤ 3.6 V, 1.8 V ≤ AVSS0 ≤ 3.6 V, VSS = AVSS0 = VSS_USB = 0 V, T_a = –40 to +105°C
Item
Symbol Min.
Typ.*⁷
Max.
Unit
Test
Conditions
Analog power During A/D conversion (at high-speed conversion)
supply current _{Waiting for A/D (all units)}
I_AVCC
—
—
0.7
1.2 mA
—
0.3 μA
During D/A conversion (per channel)*⁵
—
—
1.5 mA
Reference
power supply
current
During A/D conversion (at high-speed conversion)
Waiting for A/D conversion (all units)
I_REFH0 —
25
52 μA
—
—
60 nA
Temperature
sensor*⁶
I_TEMP
—
75
— μA
LDV1, 2
USB
operating
current
Per channel
I_LVD
—
0.15
— μA
During USB communication operation under the following settings I_USBH*² —
and conditions
4.3
(VCC)
— mA
 Host controller operation is set to full-speed mode
0.9
Bulk OUT transfer (64 bytes) × 1,
(VCC_USB)
bulk IN transfer (64 bytes) × 1
*⁴
 Connect peripheral devices via a 1-meter USB cable from
the USB port.
During USB communication operation under the following settings I_USBF*² —
and conditions
3.6
(VCC)
— mA
 Function controller operation is set to full-speed mode
1.1
Bulk OUT transfer (64 bytes) × 1,
(VCC_USB)
bulk IN transfer (64 bytes) × 1
*⁴
 Connect the host device via a 1-meter USB cable from the
USB port.
During suspended state under the following setting and conditions I_SUSP*³ —
 Function controller operation is set to full-speed mode
0.35
(VCC)
— μA
(pull up the USB0_DP pin)
170
 Software standby mode
(VCC_USB)
 Connect the host device via a 1-meter USB cable from the
*⁴
USB port.
Note 1. The reference power supply current is included in the power supply current value for D/A conversion.
Note 2. Current consumed only by the USB module.
Note 3. Includes the current supplied from the pull-up resistor of the USB0_DP pin to the pull-down resistor of the host device, in addition
to the current consumed by this MCU during the suspended state.
Note 4. When VCC = VCC_USB = 3.3 V.
Note 5. The value of the current flowing to VCC.
Note 6. Current consumed by the power supply (VCC).
Note 7. When VCC = AVCC0 = VCC_USB = 3.3 V.
Table 5.13 DC Characteristics (11)
Conditions: 1.8 V ≤ VCC = VCC_USB ≤ 3.6 V, 1.8 V ≤ AVSS0 ≤ 3.6 V, VSS = AVSS0 = VSS_USB = 0 V, T_a = –40 to +105°C
Item
Symbol
Min.
Typ.
Max.
Unit
Test Conditions
RAM standby voltage
V_RAM
1.8
—
—
V
R01DS0190EJ0130 Rev.1.30
May 31, 2016
Page 64 of 127