|
SE98A Datasheet, PDF (41/43 Pages) NXP Semiconductors – DDR memory module temp sensor, 1.7 V to 3.6 V | |||
|
◁ |
NXP Semiconductors
SE98A
DDR memory module temp sensor, 1.7 V to 3.6 V
Table 30. Abbreviations â¦continued
Acronym
Description
RDIMM
Registered Dual In-line Memory Module
SO-DIMM
Small Outline Dual In-line Memory Module
PC
Personal Computer
POR
Power-On Reset
RWP
Reversible Write Protection
SMBus
System Management Bus
SPD
Serial Presence Detect
15. Revision history
Table 31. Revision history
Document ID Release date
Data sheet status
Change notice
Supersedes
SE98A_2
Modiï¬cations:
20090806
Product data sheet
-
SE98A_1
⢠Section 1 âGeneral descriptionâ, 3rd paragraph, 1st sentence: appended âusing an open-drain output
that can be pulled up between 0.9 V and 3.6 Vâ.
⢠Section 2 âFeaturesâ: 1st bullet item re-written.
⢠Table 1 âOrdering informationâ, Table note [1]: changed from âJEDEC WCE-3, TDFNâ to
âJEDEC VCED-3 PSON8â
⢠Section 7.3.2.1 âAlarm windowâ:
â 1st Advisory notiï¬cation, Competitor device: appended â(CEVNT)â to end of phrase
â 1st Advisory notiï¬cation, Work-around: appended â(CEVNT)â to end of phrase
â 2nd Advisory notiï¬cation, Competitor devices: changed from â... when new UPPER or LOWER and
Event bit 3 (EOCTL) are set ... â to âwhen new UPPER or LOWER Alarm Windows and the EVENT
output are set ...â
â 2nd Advisory notiï¬cation, Work-around: appended â(EOCTL = 1)â to end of phrase
⢠Section 7.3.2.2 âCritical tripâ
â 1st paragraph, last sentence: changed from â... through the Clear EVENT bit ...â
to â... through the Clear EVENT bit (CEVNT) ...
â Advisory notiï¬cation, Competitor devices: re-written
â Advisory notiï¬cation, Work-around: changed from âWait at least 125 ms before enabling EVENT
output, Intel will change Nehalem BIOS so that Tth(crit) is set for more than 125 ms before Event
bit 3 (EOCTL) is enabled and Event value is checked.â to âWait at least 125 ms before enabling
EVENT output (EOCTL = 1), Intel will change Nehalem BIOS so that Tth(crit) is set for more than
125 ms before EVENT output is enabled and Event value is checked.
⢠Section 7.7 âSMBus Time-outâ: added second âRemarkâ statement.
⢠Section 7.8 âSMBus ALERTâ: added second âRemarkâ statement.
⢠Section 9.3 âThermal considerationsâ: symbols used in Equation 1 are updated to match those used
in characteristics tables
⢠(old) Table 27 âSMBus AC characteristicsâ replaced in its entirety by (new) Table 27 âSMBus AC
characteristicsâ
⢠(old) Figure 27 âDeï¬nition of timing for F/S-mode devices on the I2C-busâ replaced by Figure 27 âAC
waveformsâ
SE98A_1
20090305
Product data sheet
-
-
SE98A_2
Product data sheet
Rev. 02 â 6 August 2009
© NXP B.V. 2009. All rights reserved.
41 of 43
|
▷ |