74HCT9046A Datasheet, PDF (16/43 Pages) NXP Semiconductors – PLL with bandgap controlled VCO

NXP Semiconductors
74HCT9046A
PLL with band gap controlled VCO
Table 5. Static characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
V_OH
HIGH-level output voltage
V_OL
LOW-level output voltage
I_I
input leakage current
R1
resistor 1
R2
resistor 2
C1
capacitor 1
pin VCO_OUT; V_CC = 4.5 V;
V_I = V_IH or V_IL
I_O = −20 µA
I_O = −4.0 mA
pin VCO_OUT; V_CC = 4.5 V;
V_I = V_IH or V_IL
I_O = 20 µA
I_O = 4.0 mA
pins C1A and C1B; V_CC = 4.5 V;
V_I = V_IH or V_IL; I_O = 4.0 mA
pins INH and VCO_IN;
V_CC = 5.5 V; V_I = V_CC or GND
V_CC = 4.5 V
V_CC = 4.5 V
V_CC = 4.5 V
V_{VCO_IN}
voltage on pin VCO_IN
Demodulator section
R_s
series resistance
V_offset
offset voltage
R_dyn
dynamic resistance
General
I_CC
supply current
∆I_CC
additional supply current
C_I
input capacitance
T_amb = −40 °C to +85 °C
Phase comparator section
V_IH
HIGH-level input voltage
V_IL
LOW-level input voltage
over the range specified for R1
V_CC = 4.5 V
V_CC = 5.0 V
V_CC = 5.5 V
V_CC = 4.5 V; at R_s > 300 kΩ the
leakage current can influence
V_{DEM_OUT}
VCO_IN to V_{DEM_OUT}; V_CC = 4.5 V;
V_I = V_{VCO_IN} = 0.5V_CC; values
taken over R_s range; see Figure 17
DEM_OUT; V_CC = 4.5 V;
V_{DEM_OUT} = 0.5V_CC
disabled; V_CC = 5.5 V;
pin INH at V_CC
pin INH; V_I = V_CC − 2.1 V; V_CC =
4.5 V; other inputs at V_CC or GND;
pins SIG_IN and COMP_IN;
V_CC = 4.5 V; DC coupled
pins SIG_IN and COMP_IN;
V_CC = 4.5 V; DC coupled
Min Typ Max Unit
4.4 4.5 -
V
3.98 4.32 -
V
-
0
0.1 V
-
0.15 0.26 V
-
-
0.40 V
-
-
±0.1 µA
3
-
3
-
40 -
300 kΩ
300 kΩ
no pF
limit
1.1 -
1.1 -
1.1 -
3.4 V
3.9 V
4.4 V
50 -
300 kΩ
-
±20 -
mV
-
25 -
Ω
-
-
8.0 µA
-
100 360 µA
-
3.5 -
pF
3.15 -
-
-
-
V
1.35 V
74HCT9046A_6
Product data sheet
Rev. 06 — 15 September 2009
© NXP B.V. 2009. All rights reserved.
16 of 43