DE1E3KX332MN5AA01 Datasheet, PDF (76/84 Pages) Murata Manufacturing Co., Ltd. – Safety Standard Certified Ceramic Capacitors/ High Voltage Ceramic Capacitors

12
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
C85E.pdf
Apr.7,2014
Type KJ Specifications and Test Methods
Continued from the preceding page.
No.
Item
High
19
Temperature
Exposure
(Storage)
Capacitance
Change
D.F.
I.R.
Appearance
Within ±20%
Specifications
Char.
B, E
Specifications
D.F.V5.0%
1000MΩ min.
No marked defect except color change of outer
coating.
20
Thermal
Shock
Capacitance
Change
D.F.
Char.
B
E
Char.
B, E
Capacitance Change
Within ±10%
Within ±20%
Specifications
D.F.V5.0%
I.R.
Appearance
3000MΩ min.
No marked defect
Capacitance
Change
21
Resistance to
Solvents
D.F.
Char.
B
E
Char.
B, E
Capacitance Change
Within ±10%
Within ±20%
Specifications
D.F.V5.0%
I.R.
Appearance
3000MΩ min.
No marked defect
22
Biased
Humidity
Capacitance
Change
D.F.
Char.
B
E
Char.
B, E
Capacitance Change
Within ±10%
Within ±15%
Specifications
D.F.V5.0%
I.R.
Appearance
3000MΩ min.
No marked defect
Capacitance
Change
Char.
B
E
Capacitance Change
Within ±10%
Within ±20%
D.F.
Char.
B, E
Specifications
D.F.V5.0%
23
Moisture
Resistance
I.R.
3000MΩ min.
Test Method
Set the capacitor for 1000±12 hrs. at 150±3°C.
Pre-treatment:
Capacitor should be stored at 125±3°C for 1 hr., then placed
at room condition* for 24±2 hrs.
Post-treatment:
Capacitor should be stored for 24±2 hrs. at room condition.*
The capacitor should be subjected to 300 cycles.
Step
1
2
Temperature (ºC)
-55+0/-3
125+3/-0
Time (min)
30
30
Pre-treatment:
Capacitor should be stored at 125±3°C for 1 hr., then placed
at room condition* for 24±2 hrs.
Post-treatment:
Capacitor should be stored for 24±2 hrs. at room condition.*
Per MIL-STD-202 Method 215
Solvent 1: 1 part (by volume) of isopropyl alcohol
3 parts (by volume) of mineral spirits
Solvent 2: Terpene defluxer
Solvent 3: 42 parts (by volume) of water
1 part (by volume) of propylene glycol
monomethyl ether
1 part (by volume) of monoethanolomine
Apply the rated voltage and DC1.3+0.2/-0V (add 6.8kΩ resistor)
at 85±3°C and 80 to 85% humidity for 1000±12 hrs.
Pre-treatment:
Capacitor should be stored at 125±3°C for 1hr., then placed
at room condition* for 24±2 hrs.
Post-treatment:
Capacitor should be stored for 24±2 hrs. at room condition.*
Apply 24 hrs. of heat (25 to 65°C) and humidity (80 to 98%)
treatment shown below, 10 consecutive times.
Pre-treatment:
Capacitor should be stored at 125±3°C for 1 hr., then placed
at room condition* for 24±2 hrs.
Post-treatment:
Capacitor should be stored for 24±2 hrs. at room condition.*
Humidity Humidity Humidity Humidity Humidity
°C
90-98% 80-98% 90-98% 80-98% 90-98%
70
65
60
55
50
45
40
35
30
25
20
+10
-2
°C
15
10
Initial measurement
5
0
-5
-10
One cycle 24 hours
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Hours
* "Room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
74