DE1E3KX332MN5AA01 Datasheet, PDF (75/84 Pages) Murata Manufacturing Co., Ltd. – Safety Standard Certified Ceramic Capacitors/ High Voltage Ceramic Capacitors

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
C85E.pdf
Apr.7,2014
Type KJ Specifications and Test Methods
Continued from the preceding page.
No.
Item
Specifications
Robustness
15 of
Terminations
Tensile
Bending
Lead wire should not be cut off. Capacitor should
not be broken.
Test Method
As shown in the figure at right, fix the body
of the capacitor and apply a tensile weight
gradually to each lead wire in the radial
direction of the capacitor up to 10N and keep _W
it for 10±1 sec.
Each lead wire should be subjected to 5N of weight and bent
90° at the point of egress, in one direction, then returend to
its original position and bent 90° in the opposite direction at the
rate of one bend in 2 to 3 sec.
The capacitor should be individually wrapped in at least one,
but not more than two, complete layers of cheesecloth. The
capacitor should be subjected to 20 discharges. The interval
between successive discharges should be 5 sec. The UAC
should be maintained for 2 min. after the last discharge.
S1
F L1
L2
R
C1 C2
C3 Cx
Ct
Ut
Tr ^{S2 UAC L3}
L4
16 Active Flammability
The cheesecloth should not catch on fire.
Oscilloscope
C1,2 : 1μF±10%
C3 : 0.033μF±5% 10kV
L1 to 4 : 1.5mH±20% 16A Rod core choke
Ct : 3μF±5% 10kV
R
: 100Ω±2%
Cx : Capacitor under test UAC : UR±5%
F : Fuse, Rated 10A
UR : Rated Voltage
Ut
: Voltage applied to Ct
Ux
5kV
17 Passive Flammability
The burning time should not exceed 30 sec.
The tissue paper should not ignite.
time
The capacitor under test should be held in the flame in the
position that best promotes burning. Each specimen should
only be exposed once to the flame. Time of exposure to flame:
30 sec.
Length of flame : 12±1mm
Gas burner : Length 35mm min.
Inside Dia. 0.5±0.1mm
Outside Dia. 0.9mm max.
Gas
: Butane gas Purity 95% min.
Test Specimen
45°
Appearance No marked defect
Tissue
About 10mm Thick Board
The capacitor should be subjected to 1000 temperature cycles.
Capacitance
Change
18
Temperature
Cycle
D.F.
Char.
B
E
Char.
B, E
Capacitance Change
Within ±10%
Within ±20%
Specifications
D.F.V5.0%
I.R.
Dielectric
Strength
3000MΩ min.
Per Item 6
Step
1
2
3
4
Temperature (ºC)
-55+0/-3
Room temp.
125+3/-0
Room temp.
Time (min)
30
3
30
3
Cycle time: 1000 cycles
Pre-treatment:
Capacitor should be stored at 125±3°C for 1 hr., then placed
at room condition* for 24±2 hrs.
Post-treatment:
Capacitor should be stored for 24±2 hrs. at room condition.*
* "Room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
Continued on the following page.
12
73