DRQ-12-50-L48 Datasheet, PDF (23/26 Pages) Murata Power Solutions Inc. – 600W Digital Fully Regulated Intermediate DC-DC Bus Converter

DRQ-12/50-L48 Series
600W Digital Fully Regulated
Intermediate DC-DC Bus Converter
TO
OSCILLOSCOPE
CURRENT
PROBE
+Vin
+
LBUS
VIN ^–
+
CBUS
CIN
–
-Vin
CIN = 220μF, ESR < 700mΩ @ 100kHz
CBUS = 220μF, ESR < 100mΩ @ 100kHz
LBUS = 12μH
Figure 4. Measuring Input Ripple Current
+Vout
-Vout
C1 C2
SCOPE
RLOAD
C1 = 1μF; C2 = 10μF
LOAD 2-3 INCHES (51-76mm) FROM MODULE
Figure 5. Measuring Output Ripple and Noise (PARD)
Thermal Shutdown (OTP, UTP)
To prevent many over temperature problems and damage, these converters
include thermal shutdown circuitry. If environmental conditions cause the
temperature of the DC-DCs to rise above the Operating Temperature Range
up to the shutdown temperature, an on-board electronic temperature sensor
will power down the unit. When the temperature decreases below the turn-on
threshold set in the command recover temp is (OT_FAULT_LIMIT-MFR_OT_
FAULT_HYS), the hysteresis is defined in general electrical specification
section. The OTP and hysteresis of the module can be reconfigured using the
PMBus. The OTP and UTP fault limit and fault response can be configured via
the PMBus.
CAUTION: If you operate too close to the thermal limits, the converter may
shut down suddenly without warning. Be sure to thoroughly test your applica-
tion to avoid unplanned thermal shutdown.
Temperature Derating Curves
The graphs in this data sheet illustrate typical operation under a variety of
conditions. The Derating curves show the maximum continuous ambient air
temperature and decreasing maximum output current which is acceptable
under increasing forced airflow measured in Linear Feet per Minute (“LFM”).
Note that these are AVERAGE measurements. The converter will accept brief
increases in current or reduced airflow as long as the average is not exceeded.
Note that the temperatures are of the ambient airflow, not the converter
itself which is obviously running at higher temperature than the outside air.
Also note that “natural convection” is defined as very flow rates which are not
using fan-forced airflow. Depending on the application, “natural convection” is
usually about 30-65 LFM but is not equal to still air (0 LFM).
Murata Power Solutions makes Characterization measurements in a closed
cycle wind tunnel with calibrated airflow. We use both thermocouples and an
infrared camera system to observe thermal performance. As a practical matter,
it is quite difficult to insert an anemometer to precisely measure airflow in
most applications. Sometimes it is possible to estimate the effective airflow if
you thoroughly understand the enclosure geometry, entry/exit orifice areas and
the fan flowrate specifications.
CAUTION: If you exceed these Derating guidelines, the converter may have
an unplanned Over Temperature shut down. Also, these graphs are all collected
near Sea Level altitude. Be sure to reduce the derating for higher altitude.
Output Short Circuit Condition
The short circuit condition is an extension of the “Current Limiting” condition.
When the monitored peak current signal reaches a certain range, the PWM
controller’s outputs are shut off thereby turning the converter “off.” This is
followed by an extended time out period. This period can vary depending on
other conditions such as the input voltage level. Following this time out period,
the PWM controller will attempt to re-start the converter by initiating a “normal
start cycle” which includes softstart. If the “fault condition” persists, another
“hiccup” cycle is initiated. This “cycle” can and will continue indefinitely until
such time as the “fault condition” is removed, at which time the converter will
resume “normal operation.” Operating in the “hiccup” mode during a fault
condition is advantageous in that average input and output power levels are
held low preventing excessive internal increases in temperature.
Remote On/Off Control
The DRQ series modules are equipped with both primary (On/Off 1, enabled,
pull up internal) and secondary (On/Off 2, disabled, pull up internal) control pins
for increased system flexibility. Both are configurable via PMBus. The On/Off
pins are TTL open-collector and/or CMOS open-drain compatible. (See general
specifications for threshold voltage levels. See also MFR_PRIMARY_ON_OFF_
CONFIG section.)
Negative-logic models are on (enabled) when the On/Off is grounded or
brought to within a low voltage (see specifications) with respect to –Vin.
The device is off (disabled) when the On/Off is left open or is pulled high to
+13.5Vdc with respect to –Vin. The On/Off function allows the module to be
turned on/off by an external device switch.
Positive-logic models are enabled when the On/Off pin is left open or is
pulled high to +13.5V with respect to –Vin. Positive-logic devices are disabled
when the On/Off is grounded or brought to within a low voltage (see specifica-
tions) with respect to –Vin. For voltage levels for On/Off 2 signal see functional
specifications.
The restart delay for this module to turn On/Off by the On/Off control pin is
100ms.
On/Off 1 or 2 Control status
Not ignored
On/Off 1 or 2 pin P LOGIC
N LOGIC
OPEN
ON
OFF
PULL HIGH
ON
OFF
PULL LOW
OFF
ON
Ignored
P LOGIC
N LOGIC
ON
ON
ON
ON
ON
ON
www.murata-ps.com/support
MDC_DRQ-12/50-L48NK.B02 Page 23 of 26