MC88915TFN55 Datasheet, PDF (19/20 Pages) Motorola, Inc – LOW SKEW CMOS PLL CLOCK DRIVER

MC88915TFN55/70/100/133/160
OUTLINE DIMENSIONS
FN SUFFIX
PLASTIC PACKAGE
CASE 776–02
ISSUE D
Y BRK
–N–
D
B 0.007 (0.180) ^M T L–M ^S N ^S
U 0.007 (0.180) ^M T L–M ^S N ^S
Z
–L–
–M–
WD
28
1
V
X
VIEW D–D
G1 0.010 (0.250) ^S T L–M ^S N ^S
A 0.007 (0.180) M T L–M S N S
H
0.007 (0.180) M T L–M S N S
Z
R 0.007 (0.180) ^M T L–M ^S N ^S
C
E
0.004 (0.100)
G
J
–T– ^SEATING
PLANE
G1
0.010 (0.250) S T L–M S N S
VIEW S
K1
K
F
VIEW S
0.007 (0.180) M T L–M S N S
NOTES:
1. DATUMS –L–, –M–, AND –N– DETERMINED
WHERE TOP OF LEAD SHOULDER EXITS
PLASTIC BODY AT MOLD PARTING LINE.
2. DIMENSION G1, TRUE POSITION TO BE
MEASURED AT DATUM –T–, SEATING PLANE.
3. DIMENSIONS R AND U DO NOT INCLUDE
MOLD FLASH. ALLOWABLE MOLD FLASH IS
0.010 (0.250) PER SIDE.
4. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN
THE PACKAGE BOTTOM BY UP TO 0.012
(0.300). DIMENSIONS R AND U ARE
DETERMINED AT THE OUTERMOST
EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR
BURRS, GATE BURRS AND INTERLEAD
FLASH, BUT INCLUDING ANY MISMATCH
BETWEEN THE TOP AND BOTTOM OF THE
PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037
(0.940). THE DAMBAR INTRUSION(S) SHALL
NOT CAUSE THE H DIMENSION TO BE
SMALLER THAN 0.025 (0.635).
INCHES
MILLIMETERS
DIM MIN MAX MIN MAX
A 0.485 0.495 12.32 12.57
B 0.485 0.495 12.32 12.57
C 0.165 0.180 4.20 4.57
E 0.090 0.110 2.29 2.79
F 0.013 0.019 0.33 0.48
G 0.050 BSC
1.27 BSC
H 0.026 0.032 0.66 0.81
J 0.020 ––– 0.51 –––
K 0.025 ––– 0.64 –––
R 0.450 0.456 11.43 11.58
U 0.450 0.456 11.43 11.58
V 0.042 0.048 1.07 1.21
W 0.042 0.048 1.07 1.21
X 0.042 0.056 1.07 1.42
Y ––– 0.020 ––– 0.50
Z
2_ 10_ 2_ 10_
G1 0.410 0.430 10.42 10.92
K1 0.040 ––– 1.02 –––
TIMING SOLUTIONS
19
BR1333 — Rev 6
MOTOROLA